Manualslib.com - The Global Manuals Library Manuals / Brands / Sony Manuals / Camera Accessories / CCU-TX7 / Service manual / PDF # SONY CCU-TX7 SERVICE MANUAL # Table of Contents Table of Contents INSTALLATION CONNECTORS AND CABLES oo Connection Connector Wiring Diagram for Cable oo MAKING OF WF MODE CONNECTOR OPERATING ENVIRONMENT ou MOUNTING ON 19-INCH RACK uu SERVICE INFORMATION BOARD LAYOUT Removal of Cabinet Replacement of Switching Regulator Replacement Of Fan oo # 3-2-4, Removal Of COU-TX7 o CIRCUIT DESCRIPTION . 0 board (DXBK-701) EXTENSION OF DXBK-701 (SDI-44 BOARD) ADJUSTMENT Switch settings Connections VIDEO SIGNAL SYSTEM ADJUSTMENT Sub-carrier Frequency Check .0 CAM H Phase Adjustment H Phase Adjustment 20.02 SYNC Phase Adjustment 0 INT SC Phase Adjustment Y CLAMP Adjustment ou Y OUT (COMP) Level Adjustment 00.0.0 Y OUT (VBS) Level Adjustment R-Y/B-Y White Black Balance Adjustment R Level Adjustment # 4-2-12. B Level Adjustment # 4-2-13. WF OUT R/B DC OFFSET Adjustment # 4-2-14. Carrier Balance Adjustment Color Vector Adjustment .0 # R-Y/B-Y OUT Level Adjustment 0.0 VBS OUT Level Adjustment .0 STAIR CASE Adjustment 0.0 # 4-2-19. WIDE ID Level Adjustment SYNC SEP Adjustment # 4-3-2. BLACK Pulse Width Adjustment SYNC Sample Hold Pulse Width Adjustment # 4-3-4, 22.5 MHz VCO DC Set Adjustment .0 Sample Pulse Width Adjustment Sample Pulse V Gate Width Adjustment # 22.5 MHz Carrier Level Adjustment Y DEMOD Carrier Balance Adjustment Y OFFSET Adjustment 2 Y Output Level Adjustment 00.0 CHROMA CABLE COMPENSATION SYSTEM ADJUSTMENT 45 MHz Carrier Level Adjustment C PLL Set Adjustment 00.0.0 # B-Y DEMOD Carrier Balance Adjustment C Ist AGC Adjustment # B-Y OUT Level Adjustment # R-Y DEMOD Carrier Balance Adjustment # R-Y OUT Level Adjustment RETURN VIDEO CABLE COMPENSATION SYSTEM Return Video Carrier Frequency Adjustment Return Video Deviation Adjustment 000 PROMPT VIDEO CABLE COMPENSATION SYSTEM RX PROMPT VIDEO RF AGC Adjustment RX PROMPT VIDEO Level Adjustment .0 Other ManualsLib Projects SONY. CAMERA CONTROL UNIT CCU-TX7 CAMERA CONTROL UNIT CCU-TX7P CAMERA OPERATION UNIT COU-TX7 SDI OUTPUT BOARD DXBK-701 SERVICE MANUAL Vol. 1 (1st Edition/Revised 1) # SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer : Check the metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. ## LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA. Leakage current can be measured by any one of three methods. 1. Acommercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. Abattery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low- voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 pF AC Pagel voltmeter (0.75V) = Earth Ground Using an AC voltmeter to check AC leakage. Fig A. # Purpose of this manual ## MANUAL STRUCTURE This manual is the Service Manual Vol. 1 of the CAMERA CONTROL UNIT CCU-TX7 (for NTSC) and CCU-TX7P (for PAL), CAMERA OPERATION UNIT COU-TX7 and SDI OUTPUT BOARD DXBK-701. This manual contains the operation manual related to the operations of this equipment, the replacement of the parts and adjustments. Related manuals to this Service Manual Vol. 1, the following manual is provided. In addition ## * Service Manual Vol. 2 Part No. 9-977-286-22 Contains semiconductor pin assignments, and schematic diagrams. parts lists, block diagrams, board illustrations CCU-TX7 (E)/V1 CCU-TX7 (E)/V1 # TABLE OF CONTENTS 1. OPERATING INSTRUCTIONS D155 V2) COUHT RIT ATP cscs ccs sstashict cee sncttegastavaspcaatelabtaneaivesn cnsneaschivensseedsnasssenseedsdesrss 1-1 DXB TOV 35 csesecascosesccossinestde Meadheesteesancecascasneeesevadenchassuersasuvsnevessveasoronesde «1-13 2. INSTALLATION 2-1. CONNECTORS AND CABLES oo... eesesesssssessseesscsenessnsssseeseeesssesueeseesenees 2-1 2-1-1. Connector Input/Output Signals 2.0... eeeeteesesesseseseeseseeeesseessneneees 2-1 2-1-2. Connection Connector ..........scceceserecsssseeessesecssssesscscessstensesserseeessatanenes 2-4 2-1-3. Wiring Diagram for Cable oo... sssseseesesonsssesesesscesseeresstenesrenseneanens 2-4 2-2. MAKING OF WF MODE CONNECTOR .......csssssssesesesscesssseeeerserseeneseeeeeees 2-4 223. COAK:- CONNECTOR sss ccsseiscescsccverseuessasaasesosesetSbonvsecteterstccntsesvonasdahsusdeaeacseets 2-5 2-4. OPERATING ENVIRONMENT ou... ..cseteessescsceseeessesssseescsseessessesssensesessenens 2-5 2-5. MOUNTING ON 19-INCH RACK uu... eessssescsessssscessesssessneesseesesssseseseeesseas 2-6 2-6. SWITCH FUNCTIONS ON BOARD uu... ccesscsssesssesessessssssseeeeeseaeeesereeenes 2-7 3. SERVICE INFORMATION 3-1. BOARD LAYOUT.............. sas bade payers dbus bus pobancusnnatensa ca arapean degeareseasans 3-1 3-2. DISASSEMBLY/INSTALLATION OF MAIN PART .......ccsecesssessssseesesenes 3-1 3-2-1. Removal of Cabinet .......ccessesescsssscssssersescseeesssssssssssssatseneseneneeerseseenees 3-1 3-2-2. Replacement of Switching Regulator ...........ccccessessessesesesseesesserseseenenenee 3-2 3-2-3. Replacement Of Fan oo... sesesssssssssssesessseesseesseseeeeessseseneseneeesssseseneneeseneens 3-3 3-2-4, Removal Of COU-TX7 o....eeesscssssessseesssenesenseseseeerseeeseneeesneneaessseeseseneeges 3-3 3-3. CIRCUIT DESCRIPTION . 0... cccsscscssesseesessssssssessssesesesssaseseseenesesenseseeeneses 3-4 CT=18T DOA Ss ecssccsess seseteccectshecvessbancide sansvasencsceddeotesscusosduasagudabacacnsatseddiayenseedsosebeuns 3-4 AA-90 DOA oo. eeeeeeeeeteeeeeeees sSieg dock Sucwaweddechuscessussebscwubsastessyasaestertesbbovbésavedesetes O-4 YD=26 Doar cessessstanst ossssscvess.decssachestesasstehigccttvabaenedecessodssadasisessorneteasedeaveseoste vere S-4 ES=20 Doar cise. cctencciecscenstavsscctssbssccscesteasscbisosetateseustescesebsosedsasteateesdeuseesteccaaseests 3-4 AU-234 DO ard wise ccsceccscivectscentzacessusdudecsiasyesciteazescastiseseaasessdsaesereeenssstncavesevodeaanestas 3-4 TO-140 Doard .......sessesscecsesessenenesessneeesseerenenesnsnsesssssssneusarseaneseeeenssentseneressaneneaennents 3-4 SDI-44 board (DXBK-701) ......escesssssesessseseecseeessssscscneseesessscssssessnsesesesesseecseeesenaes 3-4 3-4, EXTENSION OF DXBK-701 (SDI-44 BOARD) ........:cscesssseeteesessseeeeeeees BO 4. ADJUSTMENT 421. PREPARATION? dines ccadeaseuateeceaselasieavandesaedseaasiaee sitvcssacctecscsselaveaseceebevevaatidicncat 4-] 4-1-1. Equipment Required wo... cessseeseseseseneesenseressnssensssersersscersneenessoaeess 4-1 AND. -FAXtUre igoiscvscclesoiaseuctecesdenceaiupsecescseesccssccchsssevetecndusNeveciendsetesttesstcaussenssdezee 4-1 AAR. Woteaion Adiustmient aahistat aicieocsscstistecsadclnucttiouyecrenaneateoegnasitte 4-1 4-1-4. Switch settings 0... ce eeeeseseesecescerseseseeneesesseeesecsessaereseensersenspenseoneoes 4-1 4-1-5. Connections ............. des vanetstcacesenauodedetusuesacendzansedsdeswessese vaceandatauecbausvoteciveve 4-2 4-2. VIDEO SIGNAL SYSTEM ADJUSTMENT .......ccccccesscsssesssesseeesseenseenennenns 4-3 4-2-1. Sub-carrier Frequency Check .0..0.....cseseeeeceseseseeeieseeseeees eaeia vatarislgins 4-3 4-2-2. CAM H Phase Adjustment... cssssssssscssesseresseeessessetersstsenseneseseneones 4-3 4-2-3. H Phase Adjustment 20.02... cccesccesceseecerssseccsereeeseseseenersensrsesnenssesserseness 4-4 1. -2-4. SYNC Phase Adjustment 0... cesesssssesessseceececssseteeecseeteceeseseeroeeee 4-4 4-2-5. INT SC Phase Adjustment............ eee Sd co evaantoadesnevedssaseatease suubdanddcenae 4-5 4-2-6. Y CLAMP Adjustment ou... ses cscscssesneceseenerscecscceetateceesenesersenenee 4-5 4-2-7. Y OUT (COMP) Level Adjustment 00.0.0... cccsseseseceesesececcesssccececeeteeses 4-6 1. -2-8. Y OUT (VBS) Level Adjustment .........ccccsccssssecesseseees he scseueteeasess 4-6 4-2-9, R-Y/B-Y White Black Balance Adjustment... sceseeeectereeteeseees 4-7 4-2-10. G Level Adjustment ..0... ce eceseeseeeecesctesesseessecssceeesseesscesvsceasssseseaees 4-7 4-2-11. R Level Adjustment... ccsessccesseseeseneresseeenes dads se daas ch dhe Wasesecead cai 4-8 4-2-12. B Level Adjustment... cscccssssescsscsseesssessssesseeseccsscseasssssesssacsensceesesnes 4-8 4-2-13. WF OUT R/B DC OFFSET Adjustment ce ccsssessseeseeecestecsesonesees ............ 4-9 4-2-14. Carrier Balance Adjustment ............:cccccsscsesesscessensecscessssseseesereessceeesraeeas 4-9 4-2-15. Color Vector Adjustment .0.......ecessecssesesceecessecsenseneseseerensenceeteeeenes 4-10 4-2-16. R-Y/B-Y OUT Level Adjustment 0.0... cescessesseesseseeeccesssesseessenteees 4-10 4-2-17. VBS OUT Level Adjustment .0....... cece ccssscsesesseresseceeseseccesssnseessnseeseees 4-11 4-2-18. STAIR CASE Adjustment 0.0... ccccescsessescescseesesecectsesssceseeeesessesersceeons 4-11 4-2-19. WIDE ID Level Adjustment ............cc:csssesessesceseserctessesseeesscesesseeasenes 4-12 4-3. Y CABLE COMPENSATION SYSTEM ADJUSTMENT .........cssceseseeees 4-13 4-3-1. SYNC SEP Adjustment ...........cccccsscsssssessessesssseeseesserecscsessseeseesceesersenee 4-13 4-3-2. BLACK Pulse Width Adjustment .............csessssseesesenecsseesscsseesseneens 4-13 4-3-3. SYNC Sample Hold Pulse Width Adjustment ..........csssesseseeseeseenees 4-14 4-3-4, 22.5 MHz VCO DC Set Adjustment .0....... cc csssssesesscnesssseneseseescnsessees 4-14 4-3-5. Sample Pulse Width Adjustment .........cccsssssscsseseserecsssssnsseseesessessesees 4-15 4-3-6. Sample Pulse V Gate Width Adjustment cc .0.......sseseeseeteeseeeeseeees 4-15 4-3-7. 22.5 MHz Carrier Level Adjustment ...........ceccsssscessescesseesenseeesereeees 4-16 4-3-8. Y DEMOD Carrier Balance Adjustment .............cscssceccecesesesstseseeeenes 4-16 4-3-9, Y OFFSET Adjustment 2...........cccscscsssscsseccssssesceeesecseesesecsesssssessseeeesens 4-17 4-3-10.: ¥ 90" Adjustment scc.ccicccescisssscocscecventeccostseasanscaencvetivagsenssseasudueersndecsooaaes 4-17 4-3-11. Y Ist AGC Adjustment 0.0... cecseecececesecensensescsecessecensseeseseeeesenerees 4-17 4-3-12. Y Output Level Adjustment 00.0... sce ccscessseccessesescesssseseesesesesssseeseeeees 4-18 4-4, CHROMA CABLE COMPENSATION SYSTEM ADJUSTMENT .......... 4-18 4-4-1. 45 MHz Carrier Level Adjustment ..0....... ccc eeessscseescenseceeeceeesessenenes 4-18 4-4-2. C PLL Set Adjustment 00.0.0... csssssssscsscsssseescesssesesensescssssssnsesesevseeerass 4-19 4-4-3, B-Y DEMOD Carrier Balance Adjustment ...........ccsssesssereesenseneneeees 4-19 4-4-4. B-Y Crosstalk Adjustment oo. ceeectesseceesecneeteeseessoessseeseseeneesnees 4-20 4-4-5, C Ist AGC Adjustment .......eseceeesscseescsesccssnesseeerssenesecaeneeseessessenees 4-20 4-4-6. B-Y OUT Level Adjustment ..0.0. cs cseceenenseeseseeseeeesesseencseeeees 4-21 4-4-7, R-Y DEMOD Carrier Balance Adjustment ............scssccssesscececsessetenees 4-21 4-4-8. R-Y Crosstalk Adjustment .0.00.. ecco san chaz actscaeasagees dauesebadhcets 4-22 4-4-9, R-Y OUT Level Adjustment 0.00.0. ees eeseececcseeseeeneseeeestecseeseesoeeees 4-22 4-5. RETURN VIDEO CABLE COMPENSATION SYSTEM ADJUSTMENT. d.ticicceicncsnseseccnonivsagssetertsvecsnniventactugocesnevseadsceeshontanstosensstebaves 4-23 4-5-1. Return Video Carrier Frequency Adjustment ............:ccssssssseeeeeseeeees 4-23 4-5-2. Return Video Deviation Adjustment 000... eeeceeesscsenseesseneeseersenes 4-23 4-6. PROMPT VIDEO CABLE COMPENSATION SYSTEM ADJUSTMENT }nscscscssccssdscisel edi otessedscisl ceed neseupueasieeandeactadecainstieaaesdteeuttes 4-24 4-6-1. TX PROMPT VIDEO Demodulation Adjustment 00.0.0... ssscseseeess 4-24 4-6-2. RX PROMPT VIDEO Demod. Adjustment... ceseeesseneeserenees 4-25 4-6-3. RX PROMPT VIDEO RF AGC Adjustment cc .0........ccscesseeeseeeeseeenens 4-26 4-6-4. RX PROMPT VIDEO Level Adjustment .0........cccscsssssseesssoneenseseereees 4-27 CCU-TX7 (EYV1 # 4-7. TRIAX INTERFACE SYSTEM ADJUSTMENT .........ccscsssesssceetesersenees 4-27 4-7-1. Frequency Set Adjustment ............. isa dadach ice sauessoececedskexsduestevectesccey 4-27 4-7-2. INCOM Deviation Adjustment ........ cect eeseeseseesssceseceetseesesesesessaves 4-28 4-7-3. PGM Deviation Adjustment .............seceecsssessesccceesseeeesssseessessatatenees 4-28 4-7-4. INCOM Demodulation Adjustment ............ ce secssssscseessstssseseseseesseseees 4-29 4-7-5. INCOM Level Adjustment 0.0.0... cessescsecsecsessseaseoseeescesssersseensssessaes 4-29 4-7-6. MIC I Demodulation Adjustment ......... eee eesceeceeceestectsseenseeensoesses 4-30 4-7-7. MIC 1 Level Adjustment ...0...........seseesessecseeseosscosseceesesesseesosessenssseeees 4-30 4-7-8. MIC 2 Demodulation Adjustment ......... ic cesessceccesceseseesesseenssonessenens 4-31 4-7-9. MIC 2 Level Adjustment ..2...... cc ecsescssesseeeecsessesescssesnsecensesessseessnonsees 4-31 4-7-10. CAM DATA Demodulation Adjustment .............:ecsseesctsscsesonesreseeee 4-32 4-7-11. CAM TONE Adjustment ......ssccscsscsssssssssscssssssscssseesssssecsssssees onsen 4-32 CCU-TX7 (EVV1 # 1-1. CCU-TX7/TX7P # SECTION 1 OPERATING INSTRUCTIONS CCU-TX7 (EVV Y g IONPOIGsompagysemen # t " MSIAJ9AO aeeenenssnonsensene suojeaijjoeds 1. -2 "(IVE HO) HIAOO OO LONN2dO NOILLAVO ASIN JOHOOHS O1M10373 JAOWSH LON 00 ON SLUVd"HOISNI SGVAOIAUTS-Y3SN H343HONIOIANAS OLGALATYNO SOIAUAS"ANNOSH3d OLAHL40 'NOLLAVD ASIY SONGAY "MOOHS DIKLOITS yOOYs 91)0918 0}"suosied einyese}! ay)seoueydde Guiduedwoooe sejeapBuiprebe. siyj'yonpoid"ON [8p JeHES # CCU-TX7 (E)V1 yespeey{ O3GIA Ni 43" CCU-TX7 (EVV1 1. -3 deo s0JoaUUOD eiawegyun uojesedo jean £ yuOy"aued quoy'Joued LuedQ aM$.dLXU/LXL-NOD UaIsey OY}*SMOIOS vampyuoxypue aso[p joued "JaYDIMS O@PIA"O78 'JO}IUOW 4aKey BWOLUD, uMOYs('mojaq o@pia 'eyUMS NYN13Y poe ©)Ne© 3 % WO/A'E/D/E'A~B/A-YA,© © Qe© ORAIA a wears©) ©& © ( a4i, oO # M@IA19AO 1 + =~ @1GR9 L-YOD jeel91qeo dLXL/ZXL-VO déXUEXL-VOalge peixen 9qsemod 801NOS pica uamod oY {peyjddns) yndu! [GS YM LoRUOW) indur (AS WMA HOA SOWUOW indut tas UUOJBABAA WA OzE¢SH 1LXL-NOO d2XLte "e|qeyoyMs # ale e1e 8ZX1-dOUsindino O/A eu) pue UeYM) % 'g/O/ed jou (peyseuuos 'AGAMA £X1-dOW (1 (ZOY10 eesy 9qJamod'aaunos(S WMLLOPESMOYS Ou}"LXL-NOO # CCU-TX7 (EVV1 # Supjas # pue jndynoqnduy ## orpne ## WOIUALNI ## @ w0yj09S dwelt ATWL Wd qouyWOOUSLNIqouy Anduy ojpne WOOHAINI yndjno pueGunesuonoas pues0]e9]puy © @VHANYDYSUMS HAMOd JouURYOBIA ATuo ; OF s AOSPROY 0} Ndjno SID Jo sayejedoOaptA STW]SULO}UOU aS] ay) | asf) pure JouURYDpoisouUOS OY} JO9Tas :qOUY'auINJOA wooxayut sqouy WIN} yndut I Vay 01 [ouNeYp0} OF 'JoSproy (J9Aa] YOIMS ore"roaUNOD J9TTUODoI] PUNOS(fay YOMMS SUINTOA "ATO yep oypue WiOII0;0T) 0} 'peaisuy OIpNe & STIspeusis OU yTUN WosrayUTBIA "Jespeay STEY10 soauIOD NOaS-) puNosOS/} WODYALNISood OIpne sty] wWeAs0I1d) wWoosdIUT "Zz auoydororur7YOzIMS [auUeYSUsaM30q WODUALNIayy *YOIPAS B ayyureIB0O1d =THO :ANYd JENN. Isnfpesnipe WOd ANT Joy2 « « "eIOUIeD DTA « :7HDZ0} s}oauUIOD [ouURYO 0} poyouyje LXL-dD¥ oq ued 10 JoWepy(papraoid) ## Aa oy viewed aed d/XVLXI-VOyoquinu ## vIoUed ¢ oy 0} payoeuMOd Sty]'HUN Jaueg FONUDa0WsYy "durey: simp UTay]0} sIM990 V]qQUd JeIxeLy OY} poxdoUUO SI:SIYST]Ue UOYA LAOHS JOJIIpUT JUALMIISAO aly Buramod Uo pau ST YoITMs sty} Uy sTyI] eloures "oidepe $10}99NU0DUo osye pur pu'[oued 'sqouy seal 'youed juauNsn{pe ## 40.4UOIdLL.ISap foMoy 101Sul ay}uoypsado qqunaysvsauDD.Nup(22as vsawmvd Burjvisuy,, a8nd) uoyvsadQ Sqouy BIBWEDYUN UoReredo pueSqouy Seyoyms Pue SEYOUMS q/XIT/ZX1L-NOD (6 aes) s6ed juoy ayy 'seyoitMs uo polzaoy snoLeA, are ayysadpa jofeuroyur"spreog oy)quonodued WOLy 'joued a3e10do 9m)/LX.L-NOOKLS.d/PueSB [JOM SGOUY OY} SOYOMS BIDUTEDsunsayoums puesqouyueym) uoNeIedo oy)Teuondoupsey uoneiedg visweD LX¥L-NOD usaq"(payfeisur ## CCU-TX7 (EVV1 1-5 qoux ALIHM. (eng) 9OUy SLIHM (62) goux yowna {enjq) qoux MOVIE (pe) bb come G NIVDYoUAS "WGGout VAD NIXS YOUMS@ TIVLAd qoux Tivlad @ Siul JOUUoNdas @ didYOUAS 6 uoHesedo yunsayozims purSqouy eiawey O winow ° Teal sovBonvive oz o™ Sunes UILINHS @uoo88 JO1UCDUO!]9aS @Yous ALVHAdO @BONVIVE NOVIE/ALIKM oO}yas pasn purjsnfpe OApIABIOWeD "suOToUNy @yoitas L1NdLNO OL # CCU-TX7 (E)V1 ch CCU-TX7 (EVV 1-7 # ©qns-q) s10}:3009 (uld-¢zDz7E7SU @ueqY si uy ZuTPOOS "uLyTING uoHeUTULIA! 1. -1, SuIpuodsaz0o 1. sio}eNU0D Jo ot)"yuaurdinbe @QNE)pue (ad4j S10}99U09 TOdNI U-SLSOYSIMSJo sty,uoTesmojsired UONEUIWI9} sapnyout y8nomp-dooy"SOYOUMS SHWdS40}9UU09 ONAS40)98UU09 ## BIO SL dLXLU/LX.L-VO mM UO suonng Z NYNLAY WOO(490}S10JOSUUODas)asoty0}v INAD J0O}e10U0H) S10}D9UUOD yndur ouds aouarejos Jeuaisyoeyq)ysinqyeusis oapta(feusts aytsodurod Jo}feursyxo* worezTuoMouAs eM)T0} puodsazos NYNLAY si1ojsauU0D pure osoyy, JoOaprlaaq OMY,sjas "lo\depy UINjaIued speusts yndurBIAOM] 9S9q} sITed Jo*$10]93UWO9 jndut jeusts uoneztuoyoUAs oj safes 'syimiap ayisofay 40.4 suoynonasui 8unvsado -dOULXE ©TNLNOQN@)(ed4} S10paN09 XI40}93UU02 4M,JO}BUUOD ay) 0} JOIUUOD "(75 $10}98UUI09BS)0) s10}D9UOD oy dyno WoYasay speUsis atOApIAse eIoUTed 'X-¥)pure(AOyJoyxDJ 'xg speudis o 'Burkey ewoIyd pue yuauoduros speusts zB as¢ 's[eUsIS Preog01UeUO YOUMS [LUIAIUt (0Z-SA) yoaTas ayyadAq yoyndyno "TeuSts| jeubls aysoduios) pue LSAA oapia ZSqA Z$10}98UUDOS-)asot}0}B s1ojD9UNOd WO (jnd}no sfeUsts OAPIAse Indyno eiouTed Capra aIsOduIO "s[eUSIsDNAS9uAS)jeuBls(jndyno40}99UU09sTyL,B sindyno JoyauUOD €'0)SL [PUSIS ONAS'd-da B UO 10}9QUTIOD JOUOUT ULOJOARM OSPTA*JOWUUOU! Xida1nj}D!Id)JOYUOW(yndyno40}99UU09as-)v INdINO JO}aUUOD OAPTA0}B0} SAY FLUBIS OSPIAasf)2)TASJOAUO 94) "to}TWOUr YOLINOW DONRG 0) JauRg [ONUOD ampJoyas 0uley adA} /X1-dOY aqJo ;eUsIs UONIaTag "Indyno ampodAy [euSts osye0} sarjdde opBY) WoT jndjno JAA,*1OVNIUOD 8 uey © ENdLNO$10}98UU09 OIW INO$10}29UU09OG NI40}99ULI09 @WDd NI40}99UU09 @ SLY10}2auu0I@ XVOD40}99UI09 2XL-NDD 'uoHedsniiy (urdos) sty}Jo}suUOd 0}euUoo BY)BOWSY& BIA Joueg LXL-dOY [OND £-WOD "91929© AMAGOW(@pour JojmMoUT UL10J2AeM) 'apour fenuonbas W}Sk$ WOT! SLY UB JOOUUOD 0} JOJaUUOD SIT) osQ) "BIMUDfc} SLY(WI09.19}T)YX)(urd-¢ 10}09uNOD B "W9]SAS WIODIOIUT WO2-Iea,D mndjno pue yndut ore speuSts A[yqe1 pue sjeusrs woorsuy §O}BIA ST)19QUUOD SY}WOSIOUL,Wo}SAS *J0}DOUUOD ATTV"JoyauUOS L/WODUALNI st0} pattddns ot 1amod OAPIABIOWILD IOPIED ## vt ## CCU-TX7 (E141 jo dtp) Jo apts 1311 ot UO SM9IDS OA} OY} UBSOO'T juol4 jouedsmasos 0} jaued pureay}JoUo sayojytms sqouy sospe asodxe yeuloyur"spleog pied pb-IaS w{t02-4aXxa) # 92-GApreog # Zt 01 youMs UOTeUTUIIA] et) NCO'uonrtsod YoAs JaxVaIg # Ol # CCU-TX7 (E\/V1 1-9 BIOWED wos Sty) STq) TatHO SAOge AOaMpJoYIO UY 0} LXL-dOw COPIAst) payoouuod "UNoY) Woy WY payfonuos sTyyayeU! OY] JOEYJO paf[oUos 2M)02 0} payouUOd st UN Yay [aued jun st st Yo}IMSJO9]9S d/XL/LXL-NOO wrouressi oiesadoJoNUOS Wor VIBES st 0} 'wun [auRY AGOWYOITAS ApLoaTIpCapt 10U a}ouIeI dLXU/LXL-N90 OBPIA saop[ONUOD TOHLNOD stypay[oNus* TVINMON YoIMsoy} Joyjoue -AAWIS esn asn aowWsy 'uN sig)"yan dLXULXI-ND9 wunSHY, 'eseo If st "uoTo9]9S _oSf)0} SOYOIMS JO9TAS ot}adjasamp Jo[euIa}X9 J0 otf Its WOOUVATO JOMOT"YOUAMS 5S pue ATIVLY ATIWL'S@youMs TSNVdYOUMS 3GOW4YouMs TOHLNOOD # 6L Por199[28 paisnipe otf "WAMOd JOJ (speusts aq ues OF o8eI[OAWIY} Sumas 198 asnNOK 01)JE *A[TeI WAM OdWOOIS JO pue (sfeusts ATE} Sayoiims 03)asn LOVLNOD 30B}UOD Eye30 ApZOd "LLL ured amp pure 'gp 0 SI (WON) SINNIVDSMoeJOSasp),asoy0} JUaWsN{pe smaios isnfpe oypJaryrydureJoyox} ured suoydosorm "oidepe ayy,JOag]vioured prepurys Jo9]WoyZI~01 OyAue (XT) Z1+ spoag] "APotpOsUO isnfpy ures '1eq3 eu}Y6-VV'pIeog oY}useI3pueGNIore sIOWSIPUL IITayy TAAo8uelo oupOrpneJoAs] SIYAoy}pal [eULION Sunysit[Ao] WNWIXeLE St'payowal J]aupJ ATUOWay Joyeorput OIpNe paz32I10 ISI '[feJOU SsOp JOYeoIpu oY)aBuULIOATUOoy osrea s}qBI] JOyeOTpUT 'ApWeNTUIEWUT UTes"JagJT9U PalSABIS 'ITJoMOr OU]"ures IOWOIPUT SayoIMs190gasoup1 WOd NIYOUMS SINISS.YOUMS s[aagj JO AP Indyno 0 01 (ZHD) suoydororus Z JouueYD arp 19Spure 01 (THD) says T ouueYo esoy) as-)10j "AP aPO02-10 0¢-"aP 0} 940 $10729|pu! JMO] 9Y3 (jaAa] pue (THD) auoYydosoqW) J [euURYD # GNI # WAAR o2 spuodsaLIOD Gp09) ZI- €P Ajoyewtxoiddy €g0 suaeisy Afeyeurrxouddy P saduvrop 91PZi+ g pZ1+ spay Joysry Ajeyeutxoiddy oy],JojpueA sana] Jojsuey [}D) sjeusis auoydororus qare (7HO poyeorput 'siojoo oyyJaddn JoyeorpurJouuego "(ZHD) pue uoneo07 uonoun4 josuedan 1. -10 pueoy peusis 'TeuStsyndino o1 Matos BurUN-oUTy ayeur surly'syuounsnipe 1. -TX7 (E)/V1 dIQeYOITMS speUsIs(z) (© wid-¢z(jeued uid-¢ 19RD qus-qquoy WIX qns-q uid-¢z (1)AMZIAY ouWTX(1) wid-¢ UO) NODUALNI DzEzTSU SLU (1) perxenay, VadINVO ATIVUWOOUFLNI X44, 9X (doPOT (zo(syed 8 OI L) 1 Surpnyoid QI WU Fol81) OLE h)34 DOP Sp'g X Surpnyoxe POT 1 ogyX DS 007 pT %/,(soyout 'pyyym) SuOTsUStT SSB SunesedQ,ainjeradute] 1)(as sayefd soquinyy @ SL 'd-da OT ndino paposug @C L oo. 'd-daw dM ONG(1)dQ AK(1) uld-p AGOW ssooe]d OU) omper YIM SUIMOTIOJO} ammyeradura} Wes Fol) 8uoNs & "(do@ZT) UL DoOv oanjeraduiay'q1UN Ot} JO O10 DoOS OY) UT suOHe90]saUlaNXe IUN YOwal YOeaI VY) suoneis 9 239A08 sormersadurey SULIO}s0} 0} JOUILUNSues 199/Qns APO! aHe10}s 0} pasojs JO ST JOalqns SuisnSI UT unesedo) UTeI pue II ey)smopurm VISY a104\4sadRIq ploAy VION, IeON esp AA "(qovOT « : «A190,10 durep Aysnp'seoutd» Rane SpialyBuUONS oNouseU ZuNeIoues "WONPIGIA SuNTUIsULN - > "SOABM - 02 # CCU-TX7 (EVV1 1-11 - *ypey # OOOOOOOOOGOGO wejsis 1. -JauuRyo UoneUILUIe) 1. ella-p suojeoyoads'NOAPZ HOUSAH)TLLL/OGpunols JO}WODIa}U! eJOWe!qeubys77 yo wooleyu! *7uo BeWeD ydnuayuy Z-;oUUEYD 77Uo Jdnusazuy ,-jauUeYD OsIM-p'enjaoe!0 Weshs 2-|aUUeYO ngppeoueeg 0 NgPpaouejeg ngpo 'eourpedu} 009SWYO # QOOOOOO8OSOG28 - € GND; 9 WYO}SINNi 340 - 8 M2] ZHOANO/NI(D) uoHeUjWWe} 'uiayshs |-JOUURYDPapueuOIeY OuIAA-Z 0 nap 009 :eouepaduut SUYOsisseud,punos6 ONS SISSVHO # 0 EPSUTA SLL'O=" # dZXU/ZX1L-NDD OaptA TeSIG dSMOEA/SMOEC-OXG 1. -12 OD YOUMs OF O]YOUMS 843dSMOEC/SMOEG-OXoes yoadse 0} payoauUOs Sty}11UNBIA BIoWIED OMALXL/LXL-VO6:9]pure Usamjog Jo\depy ¢:p'soneljoadse vioure> Auay Buysn oy)e]oWSeY [OUDjaueg ZXL-dOY usu,Buisn 94}Biswed ZXE-NOD uoljeladg (1)40-er2-p98- OaptA"seuss XId at] A Wor ay} 94) X Woy Woy Indyno)9y] Indino) ndyno) Woy sroyTUOUT yndyno)yndino srojuOUT (s1o]2NU09 ULIOJaAeM yeustsyeusis Oapta X 5 '(ALXL-NDD) oapta pue ZEAJoy JOY (1OJD9UOD [eURIs[LUZIS x wouodusoD PUL jo (loyauu09 yeusis ISAA OaplAOAPIA SSM TAA, 7 (lojsuU0o « (Jo}D9ULOD + + (TMs[VIA10 (LXL-9.99) S19 SurAqduos pOTI-MdD « (Z | sjeusqs pue oapta Zzayy Woy indino) aysodutos # CCU-TX7 (EV 1. -2. DXBK-701 CCU-TX7 (EVV1 1-13 0} Ajduio9 JueNsind 0} puno} 'eojep pue jeyHip pejse} y useqsseiD sey eB JO} jueUdinbe SWI] OU} siy)YIM 104au}UF SABWO}SNd ey}WSN JOOOS"SeINY0}aSL Wed ey}ie sy] esay| peubisep ysij6ug JOU SUOHBOIIPOLU JNOA PIOA Pinos 4o seHueyo yenuew Aue siy} yey}ul percidde pauo|Ned (L) "S8INY:suonIpUCS DOA OU}OM} JO BuIMoTfo} GL Hed tIMALY 0} SaldWOdJOS!qns si edIAap UOLe1EedO Ajsseidxe oie sit, NOA Ayoujyne 0}eyesedo siuy'juawidinbe J q Hedqng JoOGt Hed OOF"S9iNY syjou Aew aaiAep jnjwueypue(gz)esneo 'eoueieLequl 'uonesedo # LL 1-14 # CCU-TX7 (E)V1 # pueuny uoljes07 " juowjsnipy pue 6ury4ony" Joao'] yusunsnlpy pue uO}}e907 JoSeq uoljOUuNY CCU-TX7 (E)V1 1-15 - - (panuyuoD) - sajqeg JosSBore "SMOT[OJAIAMOOTWOOT # LI A384M007 a3u4O07 pieog Joulejel CCU-TX7 (EVV1 g OaPIAdojs oY}ut juounsnipe Jey) Bnsus joasy 0} Aressadou oyne Jno si Ares UStUSN[pe 'ayeridoidde [OAd] OMeaxe s[aao] ON, ayyJopun* (gf a8nd) pure ainpasoid 8uniy,, qjuounsn{py OLNV 2) ssoid 'yuouraydun dreys Jayjo Jo uad v yA # T"YOUMSTHAN € CCU-TX7 (EV/V1 # FE # ZL SS7 preogJoureje! uaysey pur 'ALXU/LXL-NOO 9y] jo jeued UOT SY} SSO[D OY}"SMOIDS QL 1. -17 1. -18 2. -TX7 (EVV1 # SECTION 2 INSTALLATION ## 2-1. CONNECTORS AND CABLES ## 2-1-1. Connector Input/Output Sianale * MIC OUTPUT CH1/CH2 (XLR 3P, MALE) The connector input/output signals are described below. 1. Rear panel | (EXTERNAL VIEW) BNC connector: 75 Q [Input signals] ¢« GENLOCK (BNC) - * RETURN VIDEO 1/2 - * PROMPT VIDEO (BNC) : VBS/BS, (BNC) : VBS, 1.0 V p-p : VBS, 1.0 V p-p ## 1.0 V p-p No. Signal MIC OUT (G) MIC OUT (Y) MIC OUT (X) (0 dBu = 0.775 Vrms) Specifications 0 dBu/ -20 dBu (Selectable with MIC switch on AA-90 board) [Output signals] * R(BNC) : 700 mV p-p « G(BNC) : 700 mV p-p * B (BNC) : 700 mV p-p « Y (BNC) :1.0V p-p « R-Y (BNC) : 700 mV p-p :525 mV p-p * B-Y (BNC) :700 mV p-p :525 mV p-p ¢ C(BNC) :286 mV p-p (for CCU-TX7) :300 mV p-p « PIX (BNC) : 1.0 V p-p * VBS 1/2 (BNC) : 140 IRE * SYNC (BNC) _ : VBS, 0.3 V p-p, ¢ WE (BNC) : 700 mV p-p (Encoded output : 1.0 V p-p) * SDI OUT (BNC) : 800 mV p-p (for CCU-TX7) (for CCU-TX7P) (for CCU-TX7) (for CCU-TX7P) (burst) (for CCU-TX7P) negative * R/G/B, Y/R-Y/B-Y, Y/C selection (Selectable with S800, $801 on the ES-20 board) [Input/Output signals] - ¢ TRIAX: King type (for CCU-TX7) _ Fischer type (for CCU-TX7P) - * COAX (BNC) ## * WE MODE (4P, FEMALE) ## (EXTERNAL VIEW) = 0.775 Vrms) (0 dBu No. Signal Specifications 1 SEQ CONT OUT (G) - OPEN COLLECTOR . 2 SEQCONT OUT (X) 1. STAIR CASE OUT (X) #1) 4 STAIR CASE OUT (G) GND for STAIR CASE - *1) Stair Case - signal - DCO +2 V CCU-TX7 (E)/V1 2-1 « INTERCOM/TALLY (D-Sub 25P, FEMALE) O %o00000000000' 9 09900000009, O (EXTERNAL VIEW) = 0.775 Vrms) (0 dBu No. Signal Specifications GREEN TALLY (Y) IN | ON :24V DC/TTL (H)/SHORT 14 GREEN TALLY (X) IN OFF : 0 V DC/TTL (L)/OPEN RED TALLY (Y) IN ON : 24 V DC/TTL (H)/SHORT 15 RED TALLY (X) IN OFF : 0 V DC/TTL (L)/OPEN GND GND for INTERCOM REMOTE 16 CAM MIC OFF IN L: CAM INCOM MIC OFF CH2 INT IN L: CH2 INTERRUPT ON 17 CH1 INT IN L: CH1 INTERRUPT ON 4W CH2 SYSTEM RECEIVE 0 dBu BALANCED AW CH2 (R) (G) OUT 4W C#2 (R) (Y) OUT 4W C#2 (R) (X) OUT 4W CH2 (T) (G) IN 4W CH2 (T) (Y) IN 4W CH2 (T) (X) IN 2W CH2 ee ne(G) IN/OUT ~ 2W CH2 (X) IN/OUT 4W CH1 (R) (G) OUT 4W CH1 (R) (Y) OUT AW CH1 (R) (X) OUT 4W CH1 (T) (G) IN 4W CHI (T) (Y) IN 4W CHi (T) (X) IN 2W CH1 (G) IN/OUT 2W CH1 (X) IN/OUT CHASIS GND 18 4W CH2 SYSTEM TALK 0 dBu BALANCED 19 20 2W CH2 SYSTEM 0 dBu Recommended Term. imp.= 600 Q 21 4W CH1 SYSTEM RECEIVE 0 dBu BALANCED 22 10 23 11 24 12 25 13 _4W CH1 SYSTEM TALK 0 dBu BALANCED 2W CH1 SYSTEM 0 dBu Recommended Term. imp.= 600 Q * RS-232C CH1/CH2 (D-Sub 25P, FEMALE) O %o00000000000' 9 00000000009, O (EXTERNAL VIEW) = 0.775 Vrms) (0 dBu No. Signal Specifications 1 CHASSHIS GND TXDATA specification. # 3 RXDATA This is based on RS-232C 38,400 bps or 9600 bps Switchable by the internal switch on the # 4 RTS # 5 CTS # 6 DSR # 7 GND # 20 DTR CT-181 board of CCU. # * REMOTE # (10P FEMALE) 2% 62 a © @ (EXTERNAL VIEW) No. Signal 1 (SPARE) Specification -_ 2 (SPARE) 3. (SPARE) 4 __S.DATA(RCP-> _ - CCU) _RX DATA equivalent 5 # S. DATA GND 7 # S. DATA §. DATA GND (CCU > RCP) (SPARE) 9 10 POWER +12.5 V DC GND POWER +12.5 V DC IN communication rate that is based on RS-232C specification is 38,400 bps. TX DATA equivalent communication rate that is based on RS-232C specification is 38,400 bps. GND for +12.5 Vdc # 10.6 V to 17:0 Vdc 1. -2 2. -TX7 (E)/V1 # ° PGM IN (XLR 3P, FEMALE) (EXTERNAL VIEW) |No.|Signal|Specifications|||EW?| |---|---|---|---|---|---| |1|PGM IN (G)|0 dBu/ -20 dBu|||(0 dBu = 0.775 Vrms)| |2|PGM IN (X)|(Selectable with PGM switch on AA-90|No.|Signal|Specifications| ||PGM IN (Y|board|||| ||OO|COND ee a ee|1|INCOM (T) (G) IN|-60 dBu (DYNAMIC MIC)| ||||2|INCOM (T) (X) IN|-20 dBu (CARBON MIC)| ||||||| |¢|IN/OUT|3P, FEMALE MALE)|3|NCOM (R) (G) OUT|GND for HEADPHONE| ||FEMALE|MALE|4|INCOM (R) (X) OUT|-0 dBu (Max. 18 dBu)| ||||5|PGM (X) OUT|| Loop-through ® @ ® ~~, (EXTERNAL VIEW) No. Signal ## 1 GND 2 RTS CH1 (X) IN/OUT (EXTERNAL VIEW) Specifications 0 dBu/ ~10 dBu (Clear-Com) RTS CH2 (X) IN/OUT - Current drive Recomended Term. Imp.= 200 Q ## 2. Front panel ## + INTERCOM ## (XLR 5P, FEMALE) 5 OQ; 1 Be) O & O ## ¢ DCIN (XLR 4P, MALE) |No.|Signal|Specifications|||| |---|---|---|---|---|---| |1|GND|GND for DC (+)|||| |2|(SPARE)|_|||| |3|(SPARE)|_-|||| |4|DC (+) IN|DC V to 10.517 V|||| @ @ ® ® (EXTERNAL VIEW) # 2-1-2. Connection Connector Use the connectors below or the equivalent at its tip when cables are connected to each connector on the connector panel during installation and servicing. Connector name GENLOCK VIDEO 1,2 RETURN VIDEO PROMPT VIDEO R/R-Y/C 1, 2 GNN 1 B/B-Y 1,2 WF PIX VBS 1/2 SYNC COAX (BNC type) MIC CH1/CH2 RTS (38P, MALE) PGM IN RTS INTERCOM/TALLY RS-232C CH1/CH2 (25P, FEMALE) WF MODE (4P, FEMALE) REMOTE (10P, FEMALE) INTERCOM (5P, FEMALE) Connected connector/cabie -_ 1-560-069-11 plug, BNC, or B-B cable assembly (1.5 min cable length, optional) 1-508-083-00 XLR, 3-pin FEMALE or CANNON XLR-3-11C or the equivalent ## 1-508-084-00 XLR, 3-pin MALE or CANNON XLR-3-12C or the equivalent D-Sub, 25-pin male, JAE DA-25PF-N or the equivalent ## 1-560-343-11 plug, 4-pin male _ ## 1-766-848-11 plug, 10-pin male, or CCA cable assembly CCA-7-5 (supplied with RCP-TX7) 1. m max.) 1-508-370-11 XLR, 5-pin male, or CANNON XLR-5-12-C or the equivalent ## 2-1-3. Wiring Diagram for Cable ¢ CCA-7 cable ## 2-2. MAKING OF WF MODE CONNECTOR ; : ¢ When connecting plug to wave form monitor, make the plage Follow: PLUG (4P) (Sony part No. 1-560-343-11) (EXTERNAL VIEW) To wave form monitor (REMOTE) (WIRING SIDE) STAIR CASE SEQ CONT # 2-3. COAX CONNECTOR The COAX connector (BNC type) can be used for connection between the CCU and the CA with a BNC cable instead of a triaxial cable. In this case, supply the power source from outside to the CA side. And for the CA side, it is needed to modify the TRIAX harness to the COAX harness. For the CCU, the following modification is required. Disconnect the RF cable from the CN3 on the IO-141 board and reconnect it to the CN4. ## RF Sf ## 2-4. OPERATING ENVIRONMENT Operating temperature : +5 °C to +40 °C Storage temperature :-20°C to +55 °C Humidity : Noncondcnsing Supply voltage : 100 V to 240 V +10% Power consumption : 95 W (maximum) (50/60Hz) 1. Do not put the unit in a place subject to high temperature or in a location near hear sources. 2. Do not put the unit in a place subject to excessive electrical and magnetic fields. 3. Put the unit in a dry and well-ventilated place. 4. Do not put the unit in a place subject to excessive dust and mechanical shock. 5. Do not put the unit in a place subject to direct sunlight and light. (Unit: mm) CCU-TX? (E)V1 2-5 # 2-5. MOUNTING ON 19-INCH RACK Two CCU-550s can be mounted on a 19-inch EJA standard rack in parallel by using rack mount adaptor RMM-TXC7 (optional). ## Mounting 1. Tighten the four rack mount screws. B5 screws (60 mm or more long) 1. Mount the CCU-TX7/TX7P on the rack mount adaptor as shown in the figure below and tighten the four fixing screws (supplied for RMM-TXC7). 2-6 1. 2. -TX7 (E)/V1 # 2-6. SWITCH ## FUNCTIONS ON BOARD CT-181 board a £12008 o8 Esoa RV23 PROMPT LEVEL ## CT-181 Board (A SIDE) $1000 This switch is for the adjustment in the factory. Factory setting : All OFF $2002 (PROMPT SELECT TX/RX) TX : When selecting the TX mode, the CCU modulates | the VBS signal input to the PROMPT VIDEO IN connector on the CCU-TX7/TX7P, and modulated signal is sent to the CA-TX7/TX7P. RX_: When selecting the RX mode, the CA modulates the VBS signal input to the PROMPT VIDEO IN connector on the CA-TX7/TX7P, and modulated signal is sent to the CCU-TX7/TX7P. Note : When using this switch, change as follows. ¢ Incase of using the TX mode (TX side) ; 1) Disconnect CN8 and connect CN3 and CN7 on the CT-181 board. 2) Set S1 and S6 switches to "PROMPTER" side on the YD-25 board of CA-TX7/TX7P. * In case of using the RX mode (RX side) ; 1) Disconnect CN7 and connect CN3 and CN8 on the CT-181 board. 2) Set S1 and S6 switches to "AUX" side on the YD-25 board of CA-TX7/TX7P. Factory setting : TX $2011 (R TALLY POWER/CONTACT) $2013 (R TALLY DC24 V/TTL) These switches are set according to the signal sandard of the R TALLY signal input to the INTERCOM/TALLY/ PGM connnector on the CCU rear panel. For the relation between the signal and switch setting, refer to the table below. Factory setting : ($2011) POWER (S2013) DC 24 V $2012 (G TALLY POWER/CONTACT) $2014 (G TALLY DC 24 V/TTL) These switches are set according to the signal standard of the G TALLY signal input to the INTERCOM/TALLY/ PGM connector on the CCU rear panel. For the relation between the signal and switch setting, refer to the table below. Factory setting : (S2012) POWER (S2014) DC 24.V $1001 (PANEL REMOTE/LOCAL) When the RCP or COU is connected, the connected one is selected in spite of PANEL setting. Also, when both RCP and COU are connected, RCP or COU is selected according to the PANEL (REMOTE/ LOCAL) setting. Factory setting : REMOTE Note : RCP : Remote Control Panel RCP-TX7 COU : Camera Operation Unit COU-TX7 * $1002 (CONTROL MODE NORMAL/SLAVE) The RCP is only connected or both RCP and COU are connected and then the $1001 switch is set to REMOTE side. In this case, the RCPis valid, and this $1002 switch is invalid. The COU is only connected or both RCP and COU one connected, and then the $1001 switch is set to LOCAL side. In this case, the COU is valid, and this $1002 switch is used as follows ; NORMAL : COU can be used 'SLAVE _ : The operation of CCU can be used. COU can not be used. Factory setting : NORMAL Signal input method Switch Contact Power (+24 V) TTL (+5 V) Power Power $2011,$2012 Contact $2013,$2014 DC24VorTTL DC24V TTL SW1000 (MIC GAIN --- CH1) SW1001 (MIC GAIN -:- CH2) Use these screws to adjust the microphone amplifier gain for the camera adaptor. The standard level (NORM) is 0 dB, and the gain setting can be adjusted to any of 16 levels from -12 dB (MIX) to +12 dB. $1004 This switch is used to change the RS-232C Factory setting.: RS-232C side and IF BOARD. CCU-TX7 (E)/V1 2-7 AA-90 board o9 0 O° TP14 & TONE TUNE 2 LV101 5.6m TUNE S EIQ) 'OTP7 =O fo fi 0 FiveM se RV2000 SIDE TONE AA-90 Board (A SIDE) Intercom select switches (S2002, $2003, $2005, S2007) $2002 (INCOM SELECT 2W/RTS/4W) Select according to the intercom system. Factory setting : 4W # $2003 (INCOM MODE 1CH/2CH) Set to 1CH or 2CH according to the intercom system. The interface circuit of CH1 side only works with the switch set to 1CH position. Factory setting : 2CH $2005 (RTS/Clear-Com) This switch selects RTS or Clear-Com position when the $2002 switch is set to RTS position. Factory setting : RTS $2007 (RTS CH REV STD/REV) Applicable Serial No. 10801 and Higher [UC] Applicable Serial No. 40136 and Higher [CE] This switch allows RTS input/output to be switched Factory setting : STD between CH1 (PROD*!) and CH2 (ENG*') when it sets to REV. . *1 : Corresponds to PROD side of the intercom selector switch for CCU-550, CCU-550P and so on. *2 : Corresponds to ENG side of the intercom selector switch for CCU-550, CCU-550P and so on. $2003, S2005 and S2007 switches to the positions shown in the table below, according to the intercom system. Set the $2002, X : Don't care Intercom system to be connected # 4-wire system # 2-wire system RTS TW system (2CH) Clear-Com 1 ch system Clear-Com TW system $2002 $2003 $2005 $2007 4w 2w RTS 2CH X 2CH _ xX 2CH RTS X X REV STD 1CH Clear-Com STD 2CH Clear-Com = REV Remarks CH1 (CCU) <=> CH1 (RTS) CH2 (CCU) <=> CH2 (RTS) CH1 (CCU) <=> CH2 (RTS) CH2 (CCU) <=> CH1 (RTS) - * $201 (MIC 1 LEVEL) This switch sets the audio signal level of the MIC OUTPUT CH-1 connector on the CCU rear panel to 0 dBu or -20 dBu. Factory setting : 0 dBu - ° S301 (MIC 2 LEVEL) This switch sets the audio signal level of the MIC OUTPUT CH-2 connector on the CCU rear panel to 0 dBu or -20 dBu. Factory setting : 0 dBu $2004 (MIC TEST) This switch is for mixing the MIC (1 or 2) audio from the CA-TX7/TX7P with the program audio (PGM) and for monitoring the audio. CH-1 : MIC 1 audio mixes to the program audio. CH-2 : MIC 2 audio mixes to the program audio. OFF : MIC 1 audio and MIC 2 audio do not mix to the program audio. Factory setting : OFF # $2006 (RTS 200 Q ON/OFF) This switch sets to ON or OFF position for 200 Q termination in the RTS system. Usually, this switch sets to OFF position because the RTS system has 200 Q termination. Factory setting : OFF $2081 (PGM IN) This switch sets the PGM (program audio) level to 0 dBu or -20 dBu. Factory setting : 0 dBu CCU-TX7 (E)\V1 2-9 YD-26 board 'SAMPL GATE axe TP4 TPT UNE # b8@ Qom Os BLACK SH = SYNC SH 4 CZNBAGC E7 fe) ° $ 3 TP13 TP14 $Q RVI eycarmea RVIO AGC CONT OFFSET ADJ YD-26 Board (A SIDE) - * $1 (MODE AUTO/MANU) The length of a triax cable connecting the camera head and CCU is automatically detected and set. when this switch is set to AUTO. The triax cable length can be manually set using S2 (CABLE LENGTH SELECT) when this switch is set to MANU (MANUAL). Factory setting : AUTO - ¢ $3 (¥-ch 2nd AGC ON/OFF) - ¢ S4(CHROMA-ch 2nd AGC ON/OFF) These switches are used for RF AGC adjustment. set these switches to ON. Usually, ¢ §2 (CABLE LENGTH SELECT) This switch is valid when S1 is set to MANU. This switch is set to the number corresponding to the cable length. Factory setting : 0 (100 m) Switch setting 0 1 PWD Cabie length (center value) 100 m 300 m 500 m 700 m NOT IN USED CCU-TX7 (EVV1 ES-20 board RV] HeHASE RY62 sc PHASE SYNC WIOTH ava @ Av2Q) SYNC PHASE RV1 RV800 Y SETUP LEVEL (NTSC ONLY) Rv4Q OFFI CAMH: BIS) 'SC FREQUENCY $800 $C. 07180 =OUTPUT!SELECT Ci" 4 OE . SCH PHASE GMAT BAL2 BWHTBAL RWHTBAL RVSO6 «= RVEOS = ROO 515 @ & > te} 3 LEVELYCUP & @ RLY GAIN ADJ Vi! QO @ Rv504- AVS03 B-Y GAIN ADJ_B-¥ BLK TP501 RV508 ° quranAVS07 '3 O8OR OTPsoz & & GLEVEL ALY BLK BAL AMAT BAL RV509 Byso1 RVSi10 aLeve. OTP503 B MAT BAL QD Qrusiz RV513 erever BAL ves RV813 ©: S- foe) TPISTP17 ES-20 Board (A SIDE) S1 (V BLKG 19H/20H/21H) «-- NTSC only This switch sets the V blanking width to 19H, 20H, or 21H. Set this switch according to the application. Factory setting : 20H S2 (H BLKG) This switch is used for H blanking width adjustment. During factory setting, this switch is set so that the H blanking with is 10.9 +0.2 psec. Set this switch according to the application. S3 (SC 0°/180°) The SC phase can be selected to 0° or 180°. Factory setting : 0° $801 (OUTPUT 2 SELECT) *R/G/B * Y/R-Y/B-Y *Y/C This switch selects the signals of the G/R/B, Y/R-Y/B-Y, and Y/C to output the OUTPUT 2 connectors on the CCU rear panel. Factory setting : R-Y/Y/B-Y $1000 (SEQ ON +/-) Set this switch to + or - position according to the waveform monitor to be used. +: NPN open collector output -: PNP open collector output Factory setting : + S800 (OUTPUT - ° R/G/B - ° Y/R-Y/B-Y eY/C # 1 SELECT) Factory setting : R-Y/Y/B-Y CCU-TX7 (E)/V1 # DU-33 board [For the Serial No. 10601 and Higher (UC)] [For the Serial No. 40251 and Higher (CE)] ## AU-234 board DU-33 Board (A SIDE) ¢ S1 (WIDE ID ON/OFF) Set this switch to ON position when the 16:9 compatible camera is connected and used in the 16:9 mode. Factory setting : ON AU-234 Board (A SIDE) - * $5 (DYNAMIC/CARBON) Set this switch according to the type of the headset microphone connected to the INTERCOM connector on the front panel. DYNAMIC _ : Dynamic type microphone CARBON : Carbon type microphone Factory setting : DYNAMIC SDI-44 board Tr1aoo 30 BO pvsaor BYDC a Av1400 BY LEVEL RV1501 RV1S00 RYOC RY LEVEL | [J] Q % TP1s00 TP1300 RVI301 RV1300 YOC YLEveL A> Ir TP1201 £201 Oo 8° Rv904 o OB Dlaveos T3902 Z|Z o DI Blaveos TP901 RVo02 # SDI-44 Board (A SIDE) - * S701 (for factory adjustment) Factory setting: LOCK - * S601 (ADJ/OPE) This switch is used for returning the level control values of the R-Y and B-Y video signals to the factory setting. Set this switch to ADJ position and turn on the power to the main unit. Alternatively, set this switch to ADJ position and press the AUTOLEVEL (BARS) switch. Usually, set this switch to OPE position. Factory setting : OPE # * $401 (AUDIO MODE) Set this switch sets to 4CH position when the units is connected to an equipment with cannot receive SDI audio in 2CH mode. It is impossible to send audio signals to channels 3 and 4 even if this switch is set to 4CH. Usually, set this switch to 2CH position. Factory setting : 2CH CCU-TX7 (E)V1 2-13 # 3-1. BOARD LAYOUT ## 10-140 board ## SECTION 3 SERVICE INFORMATION ## 3-2. DISASSEMBLY/INSTALLATION OF MAIN PART ## 3-2-1. Removal of Cabinet 1. Removal of Front 1. 1. AU-234 board AU-234 board Front panel CCU-TX7(EVV1 3-1 1. Removal of Cover 1. Bottom cover a B 3x5 # 3-2-2. Replacement of Switching Regulator [For the Serial No. 10001 through 11000 (UC)] [For the Serial No. 40001 through 41000 (CE)] 1. Remove the top and bottom covers. (Refer to "3-2-1. Removal of Cabinet".) 2. Remove four screws (K3X6) and disconnect CN1 on the 1O-140 board and CN10, CN19 and CN20 on the MB- 693 board. Remove the rear panel. Connector (CN10) - We onnector (CN19) Connector (CN20) Switching regulator 1. When installing a new switching regulator, reverse the | above procedures. [For the Serial No. 11001 and Higher (UC)] [For the Serial No. 41001 and Higher (CE)] # 1. Remove the top cover. (Refer to "3-2-1. Removal of Cabinet'.) . Remove four screws (K3X6) and disconnect CN1 on the 10-140 board and CN10, CN19, CN20 and CN28 on the MB-693A board. Remove the rear panel. . Remove four screws (PSW3X20) and remove the fan. Connector (CN10) Cae (CN1) # 3-2-3. Replacement of Fan [For the Serial No. 11001 and Higher (UC)] [For the Serial No. 41001 and Higher (CE)] When the fan is out of order, the CAMERA POWER indicator is blinking. , Turn off the power immediately and replace the fan. Using the defective fan may reduce the service life of the equipment extremely. Before replacing the fan, be sure to turn off the power switch and unplug the power cord. ° Perform steps 1 to 3 in Section "3-2-2. Replacement of Switching Regulator" for the Serial No. 11001 and higher (UC), Serial No. 41001 and higher to remove the fan. Install a new fan in the reverse order. Connector (CN28) Connector (CN19) K3x6 Connector (CN20) # 3-2-4. Removal of COU-TX7 As for installing of COU-TX7, refer to "Installing the Camera Operation Unit" of service manual SECTION 1. Switching regulator 5. When installing a new switching regulator, reverse the above procedures. CCU-TX7(EVV1 # 3-3. CIRCUIT DESCRIPTION ## CT-181 board CT-181 board employs RF system circuit that is consists of RETURN VIDEO modulation circuit and PROMPT VIDEO modulation circuit (It becomes AUX VIDEO demodulation circuit by switching.) and microcomputer system circuit that controls the system. Microcomputer system circuit section : The program is written in the ROM (C1022) that is inserted to socket (CNI 1). ROM of built-in microcomputer is not used. Input and output of control signals between each board in CCU (included in COU) and each board are performed by serial data of 16 bit via YO EXPANDER (1C1028). There are four communication channels with outside. The SCI-1 and SCI-2 built-in microcomputer communicate with CA (via modulation and demodulation circuit ) and RCP (via RS-232C driver). The external SCI (1C1024 and 1025) communicates with command link (RS-232C-1 and RS-232C-2 on the rear panel). The RF system circuit section : RETURN VIDEO modulation circuit frequency-modulates the input signal (VBS) from RETURN VIDEO 1 or 2, and sends to the CA. Change of RETURN VIDEO 1 or 2 is switched by RETURN 1! and 2 changing switch on the CA. The PROMPT VIDEO modulation circuit amplitude- modulates the input signal (VBS) from PROMPT VIDEO on the rear panel, and sends to the CA. The PROMPT VIDEO modulation circuit becomes AUX VIDEO demodulation circuit by switching S2002 and connecting RF coaxial cable to CN3 and CN8. (lt is needed to change on the YD-25 board of CA.) Demodulated AUX VIDEO is outputted from PROMPT VIDEO on the rear panel. ## AA-90 board This board demodulates the RF signal of MIC1, MIC2, INCOM, CAM DATA and TONE sent from the CA, modulates a PGM signal, the INCOM signal and control data send to the CA. And also, this board switches the INCOM line, and switches the input /output of each audio signals. 3-4 ## YD-26 board YD-26 board demodulates Y, R-Y, B-Y, CAM SYNC and SKIN GATE. This circuit consists of cable length detection circuit, cable length compensation circuit and these demodulation circuits. The cable length detection detects from amplitude of Y modulated wave. In accordance with this, the cable compensation circuit compensates the amplitude and phase matching as cable length to modulated wave of Y or differential signal. After that, they are respectively demodulated in demodulator circuit. ## ES-20 board This board produces VBS and RGB signal from the Y, R-Y, and B-Y signals sent from the YD-26 board, switches these signals, and outputs them as WF and PIX signals. This board also generates each sync signal and color bars signal. ## AU-234 board This board inputs and outputs an INCOM signal on the front panel, displays tally signals, and turns on and off the power of camera. ## 10-140 board This board mixes the RF signal between CA and CCU with the power of the camera. ## SDI-44 board (DXBK-701) This board converts the analog video/audio signals into digital signals and outputs them as SDI signals. Video signal processing : Y, R-Y and B-Y signals sent from the ES-20 board are converted from analog to digital and subject to the double over-sampling process on the digital filter IC308. Audio signal processing : MIC1 and MIC2 signals sent from the AA-90 board are converted from analog to digital and subject to 64 times over-sampling process on IC904 and then subject to time- base compression on IC404. These digital video signals and the time-base compressed digital audio signals are mixed on IC413. After that, the parallel data is converted to serial data on IC702 and output from this board. CCU-TX7(EVV1 # 3-4. EXTENSION OF DXBK-701 (SDI-44 BOARD) 1. Disconnect two coaxial cables from the SDI-44 board. 2. Extend the SDI-44 board with the EX-564 board. To confirm the SDI signal output with the SDI- 44 board extended: Preparation: @ Coaxial connector converter : Sony part No. 1-750-881-11 @) Coaxial cable assembly: Sony part No. 1-765-112-12 @ BNC cable : . BELDEN 8281 cable or equivalent Connect @ Coaxial cable assembly, @® Coaxial connector converter, and ® BNC cable as shown below. eee 7 oe - Coaxial cable are assembly oek Coaxial connector a Equipment, Monitor @ BNC cable CCU-TX7(E\V1 3-5 # SECTION 4 ADJUSTMENT ## 4-1. Preparation ## 4-1-1. Equipment Required - * Oscilloscope (more than 300 MHz) Tektronix 2465 or equivalent * Waveform monitor/Vectorscope Tektronix 1765 or equivalent ¢ Color monitor Sony PVM-1354Q or equivalent (For NTSC) Sony PVM-1454QM or equivalent (For PAL) ¢ Video signal generator Tektronix 1410 or equivalent (For NTSC) Tektronix 1411 or equivalent (For PAL) (Color Bar signal, 10 STEP signal, SWEEP signal) - ¢ Video camera Sony DXC-637 or DXC-D30 (NTSC) Sony DXC-637P or DXC-D30P (PAL) ¢ Remote control Unit Sony RCP-TX7 (or COU-TX7 : Camera Operation Unit) ¢ Digital voltmeter ¢ Frequency counter - ¢ Audio generator ¢ Spectrum analyzer - ¢ TRIAX Cable ## 4-1-2. Fixture Extension board EX-564 (For CCU-TX7/TX7P) |$1002|NORMAL| |---|---| |$1004|All RS-232C side| |Sony part number : Sony part number :|| |$2002|TX| |J-6276-420-A J-6276-430-A|| |$2011|POWER| |$2012|POWER| |$2013|DC 24V| |$2014|DC 24V| |AA-90 $201|0 dBu| |$301|0 dBu| |$2002|4w| |$2003|2CH| |$2004|OFF| |Pattern box PTB-500 . $2005|RTS| |$2006|OFF| |Sony part number :|| |$2081|0 dBu| |J-6029-140-B|| |YD-26 =S1|AUTO| |} © Light source for test chart|| |$2|0| |$3|ON| |$4|ON| |es ES-20 $1|20H (NTSC.only)| |S2|-| |$3|0°| |$800|R-Y/Y/B-Y| |$801|R-Y/Y/B-Y| |$1000|+| Extension board | EX-565 (For CA-TX7) CCU-TX7 (EVV1 ## 4-1-3. Notes on Adjustment CAUTION - ¢ When performing STAIR CASE adjustment, connect the WF MODE connector of CCU-TX7/TX7P rear panel to the remote control connector of waveform monitor with the connecting cord. (Refer to Section 2, 2-2. "Making of WF MODE Connection") - ¢ Do not turn the following adjusting core on the YD-26 and CT-181 boards. Replace a new one when a filter is faulty. Filters on the YD-26 board and CT-181 board FL1, FL2, FL4, FL5, FL6, FL7, FL8, FL9, FLJ0, FL11, FL12, FL13, FL14, FL15 The adjustment is not required after replacing. ## 4-1-4. Switch settings When switching the following switches from a customer-set position, it is recommended to record the setting state of the customer in the table below. After adjustment is complete, be sure to return the switches to their customer-set position. Board Switch Setting during adjustment CT-181 $1000 $1001 $1002 $1004 $2002 $2011 $2012 $2013 $2014 All OFF REMOTE NORMAL All RS-232C TX POWER POWER DC 24V DC 24V Customer-set position # 4-1-5. Connections COLOR VIDEO CAMERA DXC-D30/D30P ape CAMERA ADAPTOR CA-TX7/TX7P TRIAX CABLE (30~750m) CAMERA CONTROL UNIT CCU-TX7/TX7P (CAMERA OPERATION UNIT COU-TX7/TX7P) Waveform monitor [ neeaee ## Audio connections Audio generator ## Fig-1 4 RCP-TX7 75Q ## (X) ## GND Audio generator LEVEL 6000 ADJ ®. ## Fig-2 # 4-2. Video Signal System Adjustment ## 4-2-1. Sub-carrier Frequency Check Note : Check that the GEN LOCK IN connector of CCU- TX7/TX7P rear panel is no signal. Before adjustment, warm up the frequency counter more than 30 minutes. Equipment : Oscilloscope, Frequency counter To be extended : ES-20 board Adjustment Procedure : 1. Connect the oscilloscope and the frequency counter as follows. ## 4-2-2. CAM H Phase Adjustment Equipment : Oscilloscope (CHOP mode) To be extended : ES-20 board Preparation : * $800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board - "Y/R-Y/B-Y" (Center Test point : CH1 pin 94/extension board CH2 pin 47/extension board Adjusting point : @RV1 (CAM H PHASE) /ES-20 Specification :T=0+0.05 ps position) _ board CH1 CH2 Frequency counter 2. Test point : TP1 (GND: E1) /ES-20 board Adjusting point : @RV4 (SC FREQ.)/ES-20 board Specification : [For NTSC] 3,579,545 +2 Hz [For PAL] 4,433,619 +2 Hz CCU-TX7 (E\V1 'SYNC WIOTH VE {NTSC ONLY} Y LEVEL (VBS) 'SYNC LEVEL (VBS) oO OS LEVEL RV813 GMATBAL2 BWHTBAL RWHTBAL Rv506 «= RVSOS A AV510RLeveL OTP5OS @ 'BMAT BAL pvsi2 RVS1S eveveL Rvsoz QO OO Rv504_-AV503 8-Y GAIN ADJ _B-Y BLK BAL ## ES-20 Board (A SIDE) # 4-2-3. H Phase Adjustment Equipment : Oscilloscope (CHOP mode) Video signal generator (Color Bar signal) To be extended : ES-20 board Preparation : ¢ Gen-lock . * Input color bar signal of video signal generator to the GENLOCK connector on the CCU-TX7/TX7P. Test point : CHI pin 78 (GND : pin 77)/ extension board CH2 pin 100 (GND: pin 99)/ extension board Adjusting point : @RV7 (H PHASE)/ES-20 board Adjustment Procedure : 1, Adjust @RV7 (H PHASE)/ES-20 board so that the width Tlis 0 £0.1 us. ## Pin 78 (CH-1) Pin 100 (CH-2) ## 4-2-4. SYNC Phase Adjustment : Overall white (white portion of the pattern box) : Waveform monitor : ES-20 board Object Equipment To be extended Preparation : ¢ Adjust the zoom feame matches screen. ¢ In case of RCP-TX7 IRIS AUTO Button (Control * In case of COU-TX7 IRIS AUTO/MANUAL switch control at "TELE" so that the white pattern the underscanned picture frame on the panel) - "ON" (Control panel) - 1 OUT connector/CCU rear (SYNC PHASE)/ES-20 board (SYNC WIDTHYES-20 board (HK BLKGYES-20 board NTSC] Tl = 1.35 +0.1 ps (@RV2) T2= 4.7 £0.1 us (@RV3) T3= 10.9 40.1 us (@S2) [For PAL} T1 = 1.55 £0.1 ps (@RV2) T2 =4.7 +0.1 ps (@RV3) T3 = 12.0 +0.1 us (@S2) "AUTO" panel Test point : VBS Adjusting point: @RV2 @RV3 @S2 Specification > [For ## [For NTSC] [For PAL] CCU-TX? (E)V1 # 4-2-5. INT SC Phase Adjustment Note : The SC-H phase measurement equipment (Tektronix : Waveform monitor 1765 or equivalent) is used for this adjustment. In case of using another measurement equipment, read its instruction manual carefully and then perform the following adjustment. Equipment : SC-H phase measurement equipment To be extended : ES-20 board Preparation : * Set the mode of Textronix 1765 to "SC-H" mode. ¢ Make sure that the video signal is not inputted to the GEN LOCK connector on the CCU-TX7/TX7P rear panel. Test point : VBS ## 1 OUT/CCU rear panel Adjustment Procedure : * Adujst @RV5 (SC-H PHASE)/ES-20 board so that the luminance line of BURST (SC) is the same as following figure. ## [For NTSC] ## [For PAL] ## 4-2-6. Y CLAMP Adjustment Equipment : Oscilloscope To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. Test point : TP507 (GND : E1)/ES-20 board Adjusting point : @RV515 (Y CLAMP)/ES-20 board Specification :A=0+5mV [For NTSC] {For PAL] Note : After this adjustment is completed, set the mode of Tektronix Waveform monitor 1765 to "WFM" mode. RV7 HPHasE RY6 sc PHASE SYNC WIDTH Rva@® Rv2 SYNC PHASE Ava ort 'SC FREQUENCY RVS 'SC-H PHASE RVB00 Y SETUP LEVEL (NTSC ONLY} GMATBAL2 BWHTBAL AWHTBAL - Rvs06 «= RVS0S = R500 Y LEVEL (VBS) SYNC LEVEL (VBS) oO RVE03 RYS02 o8 0° , TPIS TP17 RV514 BOCBAL RV513 B LEVEL CCU-TX7 (E\V1 ## B-Y GAIN ADJ _8-¥ BLK BAL ES-20 Board (A SIDE) # 4-2-7. Y OUT (COMP) Level Adjustment ## 4-2-8. Y OUT (VBS) Level Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. * S800 (R/G/B, Y/R-Y/B-Y, Y/C\/ES-20 board - "Y/C" Test point : G/Y/Y 1 OUT connector/CCU rear panel Equipment : Waveform monitor To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7 or * S800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board - "Y/R-Y/B-Y" (Center Test point : G/Y/Y | OUT connector /CCU rear panel COU-TX7. position) Adjustment Procedure : . Adjustment Procedure : ES-20 board [For NTSC] ## ES-20 board [For NTSC] pane] minaSeeictns | Y Level Adjustment @RV804 A= 100 +2 IRE SYNC Level Adjustment | @RV803 B = 40 +1 IRE ES-20 board [For PAL] Y Level Adjustment SYNC Level Adjustment @RV802 A= 700 +10 mV | @RV801 B= 300 +5 mV [For NTSC] [For PAL] ES-20 board [For PAL] Y Level Adjustment @RV804 SYNC Level Adjustment | @RV803 [For NTSC] [For PAL] A= 700 +10 mV B = 300 +5 mV RY6 sc PHASE SG. 0/180 §=-ouTPUuT?SELECT SYNC WIDTH Y LEVEL (vBS) SYNC LEVEL (VBS) Oo RV603. Rveo2 7) Qo ¥ Q coun RVI QScamnrnnse ANTSC ONLY) && 27 'SC FREQUENCY 2 aso Rvs SC+H PHASE of ° Rv813 "~~ fete) TPISTP17 G MATBAL2 506 BWHTBAL RWHTBAL RV505 RV500 4-6 AV510 Reve, OTPSO3 BMATBAL Q OaAvsie RVS13 8 LeveL RV504 RVSO3 1. -Y GAIN ADS _B-Y BLK BAL ES-20 Board (A SIDE) 1. -TX7 (EVV # 4-2-9. R-Y/B-Y White Black Balance Adjustment Equipment : Oscilloscope To be extended : ES-20 board Preparation : ¢ Select the BARS mode on ie RCP-TX7 or COU-TX7. Adjustment Procedure : 1. Test point : TP505 (GND : E1)/ES-20 board Specification : A=0£5 mV @RV500 C=0+5 mV @RVSO01 E=525+5mVp-p @RV502 ## 4-2-10.G Level Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : * Select the BARS mode on the RCP-TX7 or COU-TX7. * S800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board > "R/G/B" Adjustment Procedure : 1. Test point : G/Y/Y1 OUT connector/CCU rear panel Adjusting point : @RV507 (G MAT BAL1)/ES-20 board @RV506 (G MAT BAL2)/ES-20 board Specification :A=B=07) mV [For NTSC] A=B=0*) mV [For PAL] 2. Test point : TP506 (GND : E1)/ES-20 board Specification : B=0+5 mV @RV505 D=0+5mV @RV503 F=525+5mVp-p @RV504 2. Adjusting point : @RV508 (G LEVEL)/ES-20 board Specification : C= 700 +10 mV [For NTSC] C= 700 +10 mV [For PAL] [For NTSC] [For PAL] 1. Repeat procedure 1 and 2 several times. CCU-TX7 (E}/V1 1. -7 # 4-2-11. R Level Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : - ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. - * $800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board > "R/G/B" Adjustment Procedure : 1. Test point : R/R-Y/C 1 OUT connector/CCU rear panel Adjusting point : @RV509 (R MAT BAL)/ES-20 board Specification :A= 0*) mV [For NTSC] A=0*) mV [For PAL] {For NTSC] [For PAL] ## 4-2-12. B Level Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : - ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. - ¢ $800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board - "R/G/B" Adjustment Procedure : 1. Test point : B/B-Y 1 OUT connector/CCU rear panel Adjusting point : @RV512 (B MAT BAL)ES-20 board Specification :A=0 70 mV [For NTSC] A=0"0 mV [For PAL] [For NTSC] [For PAL] A 2. Adjusting point : @RV510 (R LEVEL)/ES-20 board Specification : B= 700 +10 mV [ For NTSC] B = 700 +10 [ m VFor PAL] [For NTSC} [For PAL] ## e ## B Md | 2. Adjusting point : @RV513 (B LEVELYES-20 board Specification :B=700+10 mV [For NTSC] B = 700 +10 mV [For PAL] [For NTSC} [For PAL] 1. -8 SYNC WIDTR 'SC FREQUENCY RVs SC-H PHASE Ob GMATBAL2 @ WHT BAL RWHT BAL Rvs0s = RVSO5 = RV500 TPSO1 RV5O8 lo} 8 O80Z0 2 OTPse2 & & guaroaiCQRYSO7, MAT BAL Rvsoo ALEVE, OTP503 GLEVEL 511 QO ROCBAL AYS1O ## 2 Oo BDCBAL RVS513 BLever ## B-YGAINADS_6-Y BLK BAL Y LEVEL (VBS) SYNC LevEt ves) R¥BO4 oR fete) TP17 - ES-20 Board (A SIDE) - CCU-TX7 (E\V1 # 4-2-13. WF OUT R/B DC OFFSET Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7. Test point : WF OUT connector/CCU rear panel Adjustment Procedure : * Adjust @RV511 (R DC BAL), @RV514 (B DC BAL)/ES- 20 board so that the DC levels of "R" and "B" are same as that of "G" even after the MONITOR SELECT button / RCP-TX7 is selected "R", "G" and "B". Specification : DC level +1 mV ("G") ## 4-2-14. Carrier Balance Adjustment Equipment : Vectorscope (MAX GAIN) To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. Test point .t VBS 1 OUT connector/CCU rear panel Adjustment Procedure : * Adjust @RV805 (I (V) CAL) and @RV809 (Q(U) CALY/ ES-20 board so that the luminance point of black level is located in the center of the vectorscope. _ [For NTSC] ## [For PAL] CCU-TX7 (EVV1 4-9 # 4-2-15. Color Vector Adjustment Equipment : Vectorscope, Waveform monitor To be extended : ES-20 board Preparation : - ¢ GAIN Switch/vectorscope - "75% CAL" - * Adjust the PHASE control on the vectorscope so that the burst spot is aligned to the 75% axis. ¢ Select the BARS mode on the RCP-TX7 or COU-TX7. Test point : VBS 1 OUT connector/ CCU rear panel Adjustment Procedure : 1. Adjust @RV806 (BURST LEVEL)/ES-20 board so that the burst spot is located at 75% scale mark on the vectorscope screen. 2. Adjust the following adjusting controls so that all luminance points are inside the respective "EA" mark on the vectorscope. @RV807 (BURST PHASE)/ES-20 board @RV808 ((U) LEVEL)/ES-20 board @RV810 (CHROMA LEVEL)/ES-20 board @FL800 (QUAD)/ES-20 board [For NTSC] [For PAL] ## 4-2-16. R-Y/B-Y OUT Level Adjustment Equipment : Oscilloscope To be extended : ES-20 board Preparation : - * Select the BARS mode on the RCP-TX7 or COU-TX7. - * $800 (R/G/B, Y/R-Y/B-Y, Y/C)/ES-20 board - "Y/R-Y/B-Y" (Center position) - ¢ R/R-Y/C1 OUT connector/CCU rear panel - "75 Q termination" - ¢ B/B-Y1 OUT connector/CCU rear panel - "75 Q termination" Adjustment Procedure : ES-20 board [For NTSC (UC)} Test point (GND : pin 91) Adj. point Specifications ## opvett | A= 70025mVpp ## onvat2 | B=70025mVpp ES-20 board [For PAL] Test point (GND : pin 91) Adj. point ## FRY | ping2 | @Rvatt By | pingo || @avei2, Specifications ## A = 525 45 mV p-p |B =52545mVp-p ## R-Y OUT ## B-Y OUT 1. Repeat procedure | and 2 several times. fl | 1. -10 2. -TX7 (E)\V1 # 4-2-17. VBS OUT Level Adjustment Equipment : Waveform monitor To be extended : ES-20 board Preparation : * Select the BARS mode on the RCP-TX7 or COU-TX7. Test point : VBS 1 OUT connector/CCU rear panel Adjusting point : @RV813 (VBS LEVEL)/ES-20 board Specification :A=100+1 IRE [For NTSC] A= 700 £10 mV [For PAL] [For NTSC] [For PAL] ## 4-2-18. STAIR CASE Adjustment Note : This adjustment is for temporary adjustment when repairing the STAIR CASE block. In the system set up, the readjustment is required to match the characteristic of waveform monitor. Equipment : Oscilloscope To be extended : ES-20 board Preparation : ¢ Select the BARS mode on the RCP-TX7. ¢ MONITOR SELECT button/RCP-TX7 - "SEQ" Test point : pin 76 (GND: pin 75)/ extension board Adjusting point : @RV1001/ES-20 board @RV 1000/ES-20 board Specification :A=10.0 +1 V p-p (@RV1001) B =0 +1 V de (@RV1000) 'SYNC. WIDTH og SC FREQUENCY RVS 'SC-H PHASE pole} TPI7 GMATBAL2 BWHTBAL RWHY BAL RVSO6 «= RVSO5 = R500 TPS501 508 fe) = OF0R0 RV515 Y CLP LEVEL TPSO5 Bey BLK BAL Rysot RVSO9 OTP503 RLY GAIN ADS B MAT BAL RvSO2 RV503 B-Y GAIN ADJ _8-¥ BLK BAL guarRV507, eau e Orpso2 & & AMAT BAL RVS10 nrever Orvsi2 RV513 B LEVEL ES-20 Board (A SIDE) CCU-TX? (EVV1 4-11 # 4-2-19. WIDE ## ID Level ## Adjustment ## [Forthe Serial [For the Serial ## No. 10601 and Higher (UC)] No. 40251 and Higher (CE)] Note : Before starting this adjustment, complete the adjustments as instructed in section 4-2-7, 4-2-8 and 4-2-17. Equipment : Waveform monitor To be extended : ES-20 board Preparation : Select the BARS mode on the RCP-TX7/TX7P or COU- TX7. $1/DU-33 board (on the ES-20 board) + ON Select the 16:9 mode. (How to select the 16:9 mode differs depending on the equipment connected to the unit.) [When the RCP-TX7/TX7P is connected] For details, refer to the RCP-TX7/TX7P operating instruction. ## 1. Select the advanced setting mode. 2. Press the menu selector button "OTHERS" nine times. 3. Select 16:9 with the setting button. [When the COU-TX7 is connected] For details, refer to the DXC-D30WS/D30WSP instruction. operating Switch 16:9/4:3 to the 16:9 setting mode using the advanced menu page 9 of the DXC-D30WS/D30WSP. Adjustment point: @RV 1/DU-33 board (on the ES-20 board) Adjustment Procedure : 1. Select the lines on the waveform monitor. 20 lines [NTSC] 23 lines [PAL] 2. Test point : VBS 1 OUT connector/CCU rear panel Specification : A = 70 +5 IRE [For NTSC] A = 500 +10 mV [For PAL] [For NTSC] [For PAL] (a) 4-12 ## DU-33 Board (A SIDE) CCU-TX7 (E)V1 # 4-3. Y Cable Compensation System Adjustment ## 4-3-1. SYNC SEP Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : ¢ In case of RCP-TX7 Set IRIS AUTO button to "OFF", IRIS control knob. . * In case of COU-TX7 Set IRIS AUTO/MANUAL close the lens iris by IRIS control Test point : TP4 (GND: E2)/YD-26 board Adjusting point : @LV1 (Y RF TUNE)/YD-26 board Specification -_: Level "A" = maximum level and close the lens iris by switch to "MANUAL", and knob. ## 4-3-2. BLACK Pulse Width Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TPS (GND: E2)/YD-26 board Adjusting point : @RV2 (BLACK S/H)/YD-26 board Specification : T= 1.7 +0.1 ps ig 50% Y RE TUNE wi OF LV1 a (eo) 'SAMPL GATE SAMPLSH - RVS -2 RV4 % 2 bis a OTs stacks sync sat S4 C2ng AGC & 3 Br cARA AL S TP14 8@ u Q TPs, e - RVI RVI4 RVIS OFFSET ADJ PULSET CCAR LEV one O&6 RVIT _AYLeVEL TPu TPi2 O TRIS RVI wa YD-26 Board (A SIDE) # 4-3-3. SYNC Sample Hold Pulse Width Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TP8 (GND: E2)/YD-26 board Adjusting point : @RV5 (SYNC S/H)/YD-26 board Specification :T=1.3 £0.1 us 50% ## 4-3-4. 22.5 MHz VCO DC Set Adjustment Note : Make sure that 45MHz frequency on the YM-15 board (CA-TX7/TX7P) should be correct. Equipment : Oscilloscope To be extended : YD-26 board Test point : TP9 (GND: E2)/YD-26 board Adjusting point : @RV6 (VCO DC SET)/YD-26 board Specification :A=0+30mVdc fAanp 1. -14 2. -TX7 (E)/V1 # 4-3-5. Sample Pulse Width Adjustment Equipment : Oscilloscope To be extended : YD-26 board : Test point : TP7 (GND: E2VYD-26 board Adjusting point : @RV4 (SAMPLE S/H)/YD-26 Specification :T=40.0+2.0 us board Vv Jt ## 4-3-6. Sample Pulse V Gate Width Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TP7 (GND: E2)/YD-26 board Adjusting point : @RV3 (SAMPLE GATE)/YD-26 board Adjustment Procedure : * Confirm that the sample pulses have six pulses in both odd and even fields. If not met, adjust @RV3 (SAMPLE GATE)/YD-26 board so that the sample pulses have six pulses in both odd and even fields. 6 Pulses --T 50% SAMPL GATE 3 TP26 ry ° gro e ## eat a Y bb2 Qo LV1 lack SH SYNC SH 2} TPS Ss '2nd AGC E7 ° o. 86 6 B-Y CARA BAL TP13 TP14@> 3 AVI Q RV1I0O AGC CONT RVIS RV14 OFFSET ADJ PLL SET Y BAL CARA Y CAR LEVEL TPH YUEVEL@® Rve Te12 RVI7 O RY LEVEL OE TPIg AVIS 0 SET YD-26 Board (A SIDE) CCU-TX7 (E)N1 4-15 # 4-3-7. 22.5 MHz Carrier Level Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TP10 (GND: Adjusting point : @RV7 (Y CARR YD-26 board Specification : A =400 +20 mV p-p (BW LIMIT/Oscilloscope > E5)/YD-26 board LEVEL)/ "OFF") ## 4-3-8. Y DEMOD Carrier Balance Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : * In case of RCP-TX7 Set IRIS AUTO button to "OFF", and close the lens iris by IRIS control knob. ¢ In case of COU-TX7 Set AUTO/MANUAL switch to "MANUAL", and close the lens iris by IRIS control knob. ¢ $3 (Y 2nd AGC)/YD-26 board > "OFF" Test point : TP11 (GND: E6)/YD-26 board Adjusting point : @RV8 (Y CARR BAL)/YD-26 board Specification :A= maximum level 1. -16 2. -TX7 (EyV1 # 4-3-9. Y OFFSET Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TP11 (GND: E6)/YD-26 board Adjusting point : @RV24 (Y OFFSET ADJ)/ YD-26 board Specification :A=0+3mV ## ee i ## 4-3-11. ¥Y 1st AGC Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : ¢ SI (AUTO/MANU)/YD-26 board - "AUTO" ¢ S3 (Y 2nd AGC)/YD-26 board - "OFF" Test point : TP11 (GND: E6)/YD-26 board Adjusting point : @RV1 (Y AGC CONT)/YD-26 board Specification :A=700220mV A ## 4-3-10. ¥ 90° Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : * Select the BARS mode on the RCP-TX7 or COU-TX7. Test point : TP26 (GND: E6)/YD-26 board Adjusting point : @FL3 (90° SIFT)/YD-26 board Specification :A=0+10mV [For NTSC] [For PAL] =I i ae Se ## CCU-TX7 (E)V1 4-17 # 4-3-12. Y Output Level Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation ¢ §3 (Y 2nd AGCVYD-26 board > "ON" Test point : TP11 (GND: E6)/YD-26 board Adjusting point : @RV9 (Y LEVEL)/YD-26 board Specification :A=700+7 mV p-p ## 4-4. CHROMA Cable Compensation System Adjustment ## 4-4-1. 45 MHz Carrier Level Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test poini : TP16 (GND: Adjusting point : @RV15 (C CARR YD-26 board Specification :A=400+20mVp-p (BW LIMIT/Oscilloscope > E8)/YD-26 board LEVEL)/ "OFF" ) 1. -18 'SAMPL GATE Nees 66 ss[] t o 6 TP4 TP7 'oh Q % AY2 LY BLACK S/H S4 Avs OTPS SYNC SH Oo CZnd ace § 3 - evcannsa TP14 oO 77>, RVIt €7 oO Q RV13 RV14 AVIS OFFSET ADS PULSET CCARLEV TP YLEVEL@® AVS @&e TPI2--RVI7 O URvcever iS) TP19 RVI8 ou CABLE LENGTH St O o38 YD-26 Board (A SIDE) CCU-TX7 (E)/V1 # 4-4-2. C PLL Set Adjustment Note : Make sure that 45 MHz frequency on the YM-15 board (CA-TX7/TX7P) is correct. Equipment : Oscilloscope To be extended : YD-26 board Test point : TP15 (GND: E8VYD-26 board Adjusting point : @RV14 (PLL SET)/YD-26 board Specification :A=02+30mVdc ## ANip ## 4-4-3. B-Y DEMOD Carrier Balance Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : ¢ $4 (C 2nd AGC)/YD-26 board - "OFF" Test point : TP17 (GND: E8)/YD-26 Adjusting point : @RV11 (B-Y CARR BAL)/ YD-26 board Specification -: Adjust so that the waveform SAMPLE pulse is maximum, board level of - ## yy Maximum. SAMPL GATE sampcsm - RV3 VE AGS 83 ## OO 5 6 TP4 TP7 'BhéQ 1. Q ## Me pucks# sync sit $4 exedAce { i] £ z 6 fs B-Y CARR TPi4 gry RVIT e (7) O LV1 TP3 7 a BAL ie} TP13 AVIO AGC CONT RV13 'OFFSET ADJ TPH yreve.O RVS Ore RVI7 pytever Tei2 O $2 CABLE LENGTH 1 a YD-26 Board (A SIDE) CCU-TX7 (E)/V1 4-19 # 4-4-4. B-Y Crosstalk Adjustment Note : Make sure that 45 MHz frequency on the YM-15 board (CA-TX7/TX7P) is correct. Equipment : Oscilloscope To be extended : YD-26 board Test point : TP17 (GND: E8)/YD-26 board Adjusting point : @RV13 (OFFSET ADJ)/YD-26 board Specification :A=0+3mV ## 4-4-5. C ist AGC Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : - ¢ $1 (AUTO/MAND)/YD-26 board - "AUTO" - ¢ S4(C 2nd AGCVYD-26 board > "OFF" Test point : TP17 (GND: E8)/YD-26 board Adjusting point : @RV10 (C AGC CONT)/YD-26 board Specification :A=350+20mV A 1. -20 2. -TX7 (EVV1 # 4-4-6. B-Y OUT Level Adjustment Equipment : Oscilloscope To be extended : YD-26 board Preparation : e $4 (C 2nd AGC)/YD-26 board > "ON" Test point : TP17 (GND: E8)/YD-26 board Adjusting point : @RV12 (B-Y LEVEL)/YD-26 board Specification :A=350+5mVp-p ## 4-4-7. R-Y DEMOD Carrier Balance Adjustment Equipment : Oscilloscope To be extended : YD-26 board Test point : TP18 (GND: E9)/YD-26 board Adjusting point : @RV16 (R-Y CARR BALY YD-26 board : Adjust @RV 16 so that the negative DC level is maximum. Specification GND Maximum (Negative DC level) - 'SAMPL GATE TP26 rz O TP10 § fe} YOFFSET ADS < Bee LVI RV2 Avs OTPS aacksat SYNC SH Te yuevecO Rvs Oc6 Tei2 AVI O Lpvieve OFFSET ADS PALSET $2 CABLE LENGTH YD-26 Board (ASIDE) - CCU-TX7 (E)V1 4-21 # 4-4-8. R-Y Crosstalk Adjustment Note : Make sure that 45 MHz frequency on the YM-15 board (CA-TX7/TX7P) is correct. Equipment : Oscilloscope To be extended : YD-26 board Test point : TP19 (GND: E9)/YD-26 board Adjusting point : @RV18 (90° SETVYD-26 board Specification :The SAMPLE pulse level should minimum. A=02+3mV be Ra ## 4-4-9. R-Y OUT Level Adjustment Equipment To be extended Preparation : * S4 (C 2nd AGCY/YD-26 Test point : TP19 Adjusting point : @RV17 Specification : Oscilloscope : YD-26 board board > "ON" (GND: E9)/YD-26 board (R-Y LEVEL)/YD-26 board :A=350+5mV | A Vv 1. -22 2. -TX7 (EYV1 # 4-5. RETURN VIDEO Cable Compensation System Adjustment 4-5-1. Return Video Carrier Frequency Adjustment Equipment : Spectrum analyzer To be extended : CT-181 board Preparation : * Input 10 STEP signal (sub-carrier : OFF) of video signal generator to RETURN-I connector (75 Q termination, 1.0 V p-p) on the CCU-TX7/TX7P rear panel. Test point : TP21 (GND: E12)/CT-181 board Adjusting point : @CV1 (RET FREQ)/CT-181 board ~ Specification -: 69.000 +0.005 MHz SYNC ## 4-5-2. Return Video Deviation Adjustment Equipment : Spectrum analyzer To be extended : CT-181 board Preparation : * Input 10 STEP signal (sub-carrier : OFF) of video signal generator to RETURN-1 connector (75 Q termination, 1.0 V p-p) on the CCU-TX7/TX7P rear panel. Test point : TP21 (GND: E12)/CT-181 board Adjusting point : @RV20 (RET DEV)/CT-181 board Specification :T=2.000 0.005 MHz T ## 69.0MHz CENT FREQ: 69.0MHz FFEQ SPAN: 5.0MHz ## 69.0MHz CENT FREQ: 69.0MHz FFEQ SPAN: 5.0MHz Note : Performe the adjustment of 4-5-1. "Return Video Carrier Frequency Adjustment" when the SYNC portion is moved during the adjustment. OEt001 g E12@@2 RF AGCOLY o2 = Av22 - a - PROMPT FREQ - pat 4, - LEVEL eRoMey Fun: Av23 PROMPT E18OTP220 [0 Jenomer se rx 2 Bo fo] & WS 02 L_ Jrrcmet sroog OK C71 BOARD IFSeoero Ne paer ## wo OP AD TP1001 TP2003 TP2002 TP2004 TP2001 TP2005 - ° - CT-181 Board (A SIDE) CCU-TX7 (E)\V1 4-23 # 4-6. PROMPT VIDEO Cable Compensation System Adjustment ## 4-6-1. TX PROMPT VIDEO Demodulation Adjustment Note : When performing this adjustment, the TRIAX cable less than 300 m should be used. Equipment : Waveform monitor, Video signal generator (10 STEP signal) To be extended : CT-181 board Preparation : ¢ $1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) - "PROMPT" ¢ S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) - "PROMPT" ¢ Connect CN7 and CN3 on the CT-181 board. (CCU-TX7/ TX7P) * $2002 (TX «+» RX)/CT-181 board (CCU-TX7/TX7P) > "TX" * $1 (MODEAUTO/MAN)/YD-26 board (CCU-TX7/TX7P) - "AUTO" * Input 10 STEP signal (sub-carrier : OFF) of video signal generator to PROMPT VIDEO IN connector (75 Q termination, 1.0V p-p) on the CCU-TX7 /TX7P rear panel. Test point : PROMPTER OUT (CA-TX7/TX7P) Note : To measure the video level, make 75 Q termination on the waveform monitor side. Adjusting point: @RV21 (PROMPT DEV)/ CT-181 board Specification :A=140+6IRE [For NTSC] A= 1.00 £0.05 V [For PAL]. Note : After this adjustment is completed, set as follows. - * S1 (MODE AUTO/MAN)/YD-26 board (CCU-TX7/TX7P) - "AUTO" 1. -24 2. -TX7 (E)/V1 # 4-6-2. RX PROMPT VIDEO Demod. Adjustment ## Note : Perform (PROMPT board. When performing 300 m should be used. Adjustment of CA-TX7/TX7P this adjustment only when replacing @LV2 FREQ) or @LV3 (PROMPT TUNE)/CT-181 this adjustment, the TRIX cable less than must be completed. Equipment : Waveform monitor, Video signal generator (10 STEP signal) To be extended : CT-181 board Preparation : * S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) > "AUX" ¢ S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) - "AUX" ¢ Connect CN8 and CN3 on the CT-181board. (CCU-TX7/ TX7P) * §2002 (TX <> RX)/CT-181 board (CCU-TX7/TX7P) = "RX" * S1 (MODEAUTO/MAN)/YD-26 board (CCU-TX7/TX7P) - "AUTO" * Input the SWEEP signal of the video signal generator to PROMPTER OUT connector on the CA-TX7/TX7P rear panel. Test point : PROMPTER VIDEO IN connector (CCU-TX7/TX7P rear panel) Note : To measure the video level, make 75 Q termination on the waveform monitor side. Adjusting point : @LV2 (PROMPT FREQ)/ CT-181 board @LV3 (PROMPT TUNE)/ CT-181 board Adjustment Procedure : 1. Observe the waveform monitor screen and adjust @LV3 (PROMPT TUNE)/CT-181 board so that the video waveform is appeared. 2. Adjust @LV2 (PROMPT FREQ)YCT-181 board so that the frequency response at 6 MHz portion is minimum. 3. Change the output signal of the video signal generator to 10 STEP (sub-carrier : ON) signal. 4. Re-adjust @LV3 (PROMPT TUNE)/CT-181 board so that the "A" portion at video waveform becomes flat. NOTE : If not met, Re-perform "4-6-2. RX PROMPT VIDEO Demod. Adjustment" after performing "4-6-3. RX PROMPT VIDEO RF AGC Adjustment". Note : After the adjustment is completed, set the switches as follows. ¢ S1 (AUX/PROMRTY/YD-25 board (CA-TX7/TX7P) - "PROMPT" * S6 (AUX/PROMRT)Y/YD-25 board (CA-TX7/TX7P) . ; - "PROMPT" * Connect CN7 and CN3 on the CT-181 board. (CCU-TX7/ _ TX7P) * $2002 (TX < RX) switch/CT-181 board (CCU-TX7/TX7P) - "TX" CCU-TX7 (E)V1 4-25 # 4-6-3. RX PROMPT VIDEO RF AGC ## Adjustment Note : When performing this adjustment, the TRIAX cable 50 m to 150 m should be used. Adjustment of CA-TX7 /TX7P must be completed. Equipment : Oscilloscope, Video signal generator (10 STEP signal) To be extended : CT-181 board Preparation : S1 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) => "AUX" S6 (AUX/PROMPT)YD-25 board (CA-TX7/TX7P) - "AUX" Connect CN8 and CN3 on the CT-181 board. (CCU-TX7/ TX7P) $2002 (TX <> RX)YCT-181 board (CCU-TX7/TX7P) - "RX" S1 (MODE AUTO/MAN)/YD-26 board (CCU-TX7/TX7P) - "AUTO" Input the 10 STEP (sub-carrier : ON) signal of the video signal generator to PROMPTER connector on the CA-TX7/ TX7P rear panel. ¥ Test point : PROMPTER VIDEO IN connector (CCU-TX7/TX7P rear panel) Note : To measure the video level, make 75 Q termination on the waveform monitor side. Adjusting point : @RV22 (RF AGC DLY)/CT-181 board Adjustment Procedure : ¢ Turn @RV22 (RF AGC DLY\CT-181 board fully in the clockwise direction, and then turn it slowly in the counterclockwise direction so that the V SYNC position of waveform becomes flat. (Take care not to over-turn.) Note : After this adjustment is completed, set the switches as follows. - ¢ SI (AUX/PROMPT)Y/YD-25 board (CA-TX7/TX7P) - "PROMPT" - * S6 (AUX/PROMPT)/YD-25 board (CA-TX7/TX7P) - "PROMPT" ¢ Connect CN7 and CN3 on the CT-181 board. (CCU-TX7/ TX7P) - ¢ $2002 (TX < RX)/CT-181 board (CCU-TX7/TX7P) - "TX" g [0] CN?Ko rx[01220£130 |rnowerar a ° FREQPROMPT g a PAN Aeso TP2003 °° 'TP2005 $2002 | TUNEPROMPT tv3 nv23 LEVEL PROMPT 4-26 ## 1 GAIN Mic Mic 2GAIN C8860O SW1001 CCU-TX7 (E\V1 # 4-6-4. RX PROMPT VIDEO Level Adjustment Note : When performing this adjustment, the TRIAX less than 300 m should be used. Adjustment of CA-TX7/TX7P must be completed. Equipment : Oscilloscope, Video signal generator (10 STEP signal) To be extended : CT-181 board Preparation : - ¢ S1 (AUX/PROMPTY)YD-25 board (CA-TX7/TX7P) - "AUX" - ¢ S6 (AUX/PROMPTYYD-25 board (CA-TX7/TX7P) - "AUX" - * Connect CN8 and CN3 on the CT-181 board. (CCU-TX7/ TX7P) * $2002 (TX - RX)/CT-181 board (CCU-TX7/TX7P) - "RX" - * S1 MODE AUTO/MAN)YYD-26 board (CCU TX7/TX7P) - "AUTO" - * Input the 10 STEP signal (sub-carrier : ON) of the video signal generator to PROMPTER OUT connector on the CA-TX7/TX7P real panel. , Test point : PROMPTER VIDEO IN connector (CCU-TX7/TX7P rear panel) Note : To measure the video level, make 75 Q termination on the waveform monitor side. Adjusting point : @RV23 (PROMPT LEVEL)/CT-181 board. A= 140+6 IRE [For NTSC] A= 1.00+0.05V [For PAL] ## 4-7. TRIAX Interface System Adjustment ## 4-7-1. Frequency Set Adjustment Note : Check to see that no signal is input to the INCOM connector and PGM connector on the CCU-TX7/ TX7P rear panel or the CCU-TX7/TX7P front panel. Perform the adjustment only when replacing the following part on AA-90 board. LV1, 21, 41, 81, D2, 22, 42, 62 Equipment : Frequency counter, Digital voltmeter To be extended : AA-90 board Adjustment Procedures : 1. Remove the ES-20 and CT-181 boards. 2. Turn on the power switch "ON". 3. AA-90 board (GND : El) |_| Test point | Adj. point oLvel 4.300 0.005 MHz oLv4t 3.600 +0.005 MHz ov 3.000 . +0.005 MHz o.v2t 2.500 +0.005 MHz Specifications ## INCOM ## H CONT CCU DATA Setting after Adjustment : Install the ES-20 and CT-181 boards back into position. E130 Tp220 FREQPROMPT s a $2002 TUNE PROMPT Lv3 Note : After this adjustment is completed, set the switches as follows. - ¢ S1 (AUX/PROMPTYYD-25 board (CA-TX7/TX7P) - "PROMPT" - * S6 (AUX/PROMPT)Y/YD-25 board (CA-TX7/TX7P) - "PROMPT" ¢ Connect CN7 and CN3 on the CT-181 board. (CCU-TX7/ TX7P) - ¢ $2002 (TX < RX) /CT-181 board (CCU-TX-7/TX7P) = "TX" Rv23 LEVEL PROMPT § CT-181 Board (A SIDE) CCU-TX7 (EyV1 4-27 # 4-7-2. INCOM Deviation Adjustment Equipment : Spectrum analyzer, Oscilloscope, Audio generator To be extended : AA-90 board Preparations : 1. INTERCOM CH1/CH2 switch (CA-TX7/TX7P side panel) - "CH-1" 2. INTERCOM LINE (CH1/PR1V/CH2) (CCU-TX7/TX7P) front panel - "CH-1 or CH-2" 3. $2002 (2W/RTS/4W)/AA-90 board (CCU-TX7/TX7P) => "4w" 4. Input the 400 Hz sine wave signal of the audio generator to pin 84 (X), pin 83 (Y) and pin 82 (GND)/extension board (AA-90 board). ¢ Fig-2 (Refer to 4-1-5. Audio connection.) 5. Adjust the output level of audio generator so that the level at TP43 (GND : E10)/AA-90 board is 220 mVp-p. Test point : TP3 (GND : E1)/AA-90 board Adjustment point : @RV41 (INCOM DEV)/ AA-90 board _ Specifications :A=B=6.0 +0.2 kHz ## 4-7-3. PGM Deviation Adjustment Equipment : Spectrum analyzer, Oscilloscope, Audio generator To be extended : AA-90 board Preparetions : 1. $2081 (0 dB/-20 dB)/AA-90 board (CCU-7X7/TX7P) - "0 dB" 2. Input the 350 Hz sine wave signal of the audio generator to pin 94 (X), pin 93 (Y) and pin 92 (GND)/extension board (AA-90 board). ¢ Fig-2 (Refer to 4-1-5. Audio connection.) 3. Adjust the output level of audio generator so that the level at TP44 (GND : E12)/AA-90 board is 220 mV p-p. Test point : TPS (GND : E1)/AA-90 board Adjustment point : @RV81 (PGM DEV)/AA-90 board Specifications >:A=B=7.0 £0.4 kHz Wave form image CENT FREQ: 3.6 MHz FREQ SPAN : 20 MHz A-90 POMIN 008 2088 MiC-1 LEVEL 'OB S2002$2005 SELECT INCOMRTS/CLEAR-COM {e) 8&0 AY301 tev - BY S ace Oo TPI0TP13ie [o) 3 oO O° TRSTP14 Qrveor 5 TONE TUNE LV101 sem TUNE eG, Lo? 3A ba?INCOM LeSe ks hiss ; ei 5 LV¥1 3.0M™ ay) HCONT =z $3 g8 g - = 1. e 1. -28 Wave form image CENT FREQ : 4.3 MHz FREQ SPAN : 20 MHz AA-90 Board (A SIDE) CCU-TX7 (E\V1 # 4-7-4. INCOM Demodulation Adjustment Note : Perform this adjustment only when replacing @T401/ AA-90 board. Equipment : Oscilloscope, Audio generator To be extended : AA-90 board AFM-15 board (CA-TX7/TX7P) Preparetions : 1. Input the 1 kHz sine wave signal of the audio generator to pin 2 (GND : pin 1) of INTERCOM/PROGRAM connector (5 pin) on the CA-TX7/TX7P. « Fig-1 (Refer to 4-1-5. Audio connection.) 2. Adjust the output level control of audio generator so that the pin 24 (GND: pin 12) /AFM-15 board is 220 mV p-p. Test point : TP14 (GND : E2)/AA-90 board Adjustment Procedures : 1. Set the input range of oscilloscope to DC made. Adjust the white core of @T401/AA-90 board slowly so that the DC level at TP14 (GND : E2)/AA-90 board is 1.24 £0.01 V de. ## 4-7-5. INCOM Level Adjustment Equipment : Oscilloscope, Audio generator To be extended : AA-90 board FM-15 board (CA-TX7/TX7P) Preparetion : 1. Input the 1 kHz sine wave signal of the audio generator to pin 2 (GND: pin 1) of INTERCOM/PROGRAM connector (5 pin) on the CA-TX7/TX7P. ¢ Fig-1 (Refer to 4-1-5. Audio connection.) 2. Adjust the output level control of audio generator so that the pin 24 (GND: pin 12) /AFM-15 board is 220 mV p-p. Test point : TP15 (GND : E2)/AA-90 board Adjustment point : @RV401 (INCOM LEVEL)/ AA-90 board Specifications :A=220+10 mV p-p 1. Set the input range of oscilloscope to AC mode, and adjust the blue core of @T401/AA-90 board so that the sine wave is minimum. 2. Repeat procedure 1. TUNE5.6m L101 £4G)° Fo ry) foQiks LV44 3.6m S TONES =o1P7 a fe} 4 Lyv21 2} DATACCU2.5M A31 Losng Stora e zo fou F O@,, noon olat erat 2 AA-90 Board (A SIDE) CCU-TX7 (E)V1 4-29 # 4-7-6. MIC 1 Demodulation Adjustment Note : Perform this adjustment only when replacing @T201/ AA-90 board. Equipment : Oscilloscope, Audio generator To be extended : AA-90 board Preparations : 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ CA-TX7/TX7P rear panel - "CA-LINE" 2. Input the 1 kHz sine wave signal of the audio generator to CH 1 of MIC IN (rear panel) on the CA-TX7/TX7P. ¢ Fig-2 (Refer to 4-1-5. Audio connection.) 3. Adjust the output level control of audio generator so that the pin 19 (GND: pin 12)/AFM-15 board is 220 mV p-p. Test point : TP8 (GND : E2)/AA-90 board Adjustment Procedures : 1. Adjust the white core of @T201/AA-90 board slowly so that the DC level at TP8 (GND : E2) /AA-90 board is 1.24 +0.01 V de. ## 4-7-7. MIC 1 Level Adjustment Equipment To be extended : Oscilloscope, : AA-90 board AFM-15 board Audio generator (CA-TX7/TX7P) Preparations : 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ CA-TX7/TX7P rear panel '-"CA-LINE" 2. Input the 1 kHz sine wave signal of the audio generator to CH 1 of MIC IN (rear panel) on the CA-TX7/TX7P. * Fig-2 (Refer to 4-1-5. Audio connection.) 3. Adjust the output level control of audio generator so that the pin 19 (GND: pin 12) / AFM-15 board is 220 mV p-p. 4. S201 (0 dB/-20 dBV/AA-90 board - 0 dB Test point : TP10 (GND : E2)/AA-90 board Adjustment point : @RV201 (MIC 1 LEVEL)/ AA-90 board 1100 + 50 mV p-p 1.24 + 0.01 Vde GND 2. Set the input range of oscilloscope to AC mode, and adjust the blue core of @T201/AA-90 board so that the sine wave is minimum. Minimum 1. Repeat procedure 1. 2. -30 3. -TX7 (E\V1 # 4-7-8. MIC 2 Demodulation Adjustment Note : Perform this adjustment only when replacing @T301/ AA-90 board. Equipment : Oscilloscope, Audio generator To be extended : AA-90 board AFM-15 board (CA-TX7/TX7P) Preparations : 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ CA-TX7/TX7P - "CA-LINE" 2. Input the 1 kHz sine wave signal of the audio generator to CH 2 of MIC IN (rear panel) on the CA-TX7/TX7P. ¢ Fig-2 (Refer to 4-1-5. Audio connection.) 3. Adjust the output level control of audio generator so that the pin 17 (GND: pin 12)/AFM-15 board is 220 mV p-p. Test point : TP11 (GND : E2)/AA-90 board Adjustment Procedures : 1. Adjust the white core of @T301/AA-90 board slowly so that the DC level at TP11 (GND : E2) /AA-90 board is 1.24 +0.01 V de. ## 4-7-9. MIC 2 Level Adjustment Equipment To be extended : Oscilloscope, : AA-90 board AFM-15 board Audio generator (CA-TX7/TX7P) Preparations : 1. AUDIO SELECT switch (CAMERA/CA-MIC/CA-LINE)/ CA-TX7/TX-7P - "CA-LINE" 2. Input the 1 kHz sine wave signal of audio generator to CH 2 of MIC IN (rear panel) on the CA-TX7/TX7P. ¢ Fig-2 (Refer to 4-1-5. Audio connection.) 3. Adjust the output level control of audio generator so that the pin 17 (GND: pin 12)/AFM-15 board is 220 mV p-p. 4. S301 (0 dB/-20 dB)/AA-90 board - "0 dB" Test point : TP13 (GND : E2)/AA-90 board Adjustment point : @RV301 (MIC 2 LEVEL) . AA-90 board Specifications :A=1100+50mVp-p 1. + 0.01 Vde GND 2. Set the input range of oscilloscope to AC mode, and adjust the blue core of @T301/AA-90 board so that the sine wave is minimum. Minimum 1. Repeat procedure 1. L441 jem 1. ol TUNE5.6m LV101 edi S% S fo O17 LV21DATACCU2.5M gy, Le "é AS7-00N 41834910 © GO toes: 002s byte AareoN lt LoS Z00zS S00gS 4103735 NOON! NOO-UYSTOSLE z AA-90 Board (A SIDE) CCU-TX7 (E)\/V1 4-31 # DATA Demodulation Adjustment 4-7-10. CAM Notes : - ¢ This adjustment for the following cameras must be completed before this adjustment. [For NTSC] DXC-637 or DXC-D30 [For PAL] DXC-637P or DXC-30P - * Perform the adjustment only when replacing @LV101 (5.6 MHz TUNE)/AA-90 board. Equipment : Oscilloscope 20 MHz BW Limit : ON ee made :DC To be extended =: AA-90 board Test point TP6 (GND : E2)/AA-90 board Adjustment point : @LV101 (5.6 MHz TUNE) AA-90 board Specifications : -100 +40 mV dc ## 4-7-11. CAM TONE Adjustment Notes: ¢ This adjustment for the Pollowinw cameras must be completed before this adjustment. [For NTSC] DXC-637 or DXC-D30 {For PAL] DXC-637P or DXC-30P Equipment : Oscilloscope (DC mode) To be extended =: AA-90 board Test point : TP7 (GND : E2)/AA-90 board Adjustment point : @RV101 (TONE TUNE)/ AA-90 board Adjustment Procedures : 1. @RV101 (TONE TUNE)/AA-90 board - "Mechanical center" 2. Turn @RV1I01 (TONE TUNE)/AA-90 board slowly clockwise and stop it at the point where the sine. wave signal just appears. Measure the DC voltage "a"---Fig-1 Equal (a) : Turn slowly clockwise Mechanical center 3. Turn @RV101 (TONE TUNE)/AA-90 board slowly counterclockwise and stop it at the point where the sine wave signal just appears. Measure the DC voltage "b"---Fig-2 Neate eet et aorta" Equal (a) Turn slowly counterclockwise Equal (b) 4, Adjust the DC level with @RV101 (TONE TUNE)/AA- 90 board so that "a" is equal to "b"---Fig-3 teen wet esate eettae" Equal (a) ## @RV101 (A=B) et atetee er scetsuesnensne Equal (b) (fig. 3) : 1. -32 2. -TX7 (E)/V1 ||ManualsLib Projects| |---|---| ||www.manualslib.com| ||www.manualslib.de| ||www.manualslib.es| ||www.manualslib.fr| ||www.manualslib.nl| ||www.manualslib.mx| ||www.manualslib.tech 30+ Languages|